PRO-POINT 8604548 Mode D'emploi

8604548
PRO,POINT
Magnetic Force
Feature(s)
SAFETY
WARNING! Read and understand
using this tool. The operator
precautions to reduce the risk of personal
damage to the equipment.
Keep this manual for safety
or inspection and maintenance
Always wear impact
and side protection for the eyes.
equipment should comply
Z87.1 standards based
2. Wear gloves that provide
work materials.
3. Use the correct tool for the job. This tool
for a specific function.
use it for an unintended
4. All magnets need to be kept at a safe distance from all
magnetic storage devices,
5. Ensure that the square
OFF position when not in contact
metals. The magnet can be left ON or OFF indefinitely
without harm. When ON and near ferromagnetic
there will be a sudden
6. Never use a square welding
any materials, although
and bolts, metal shavings,
All products are designed
7.
conditions, do not use underwater
hazardous environment.
Do not use the magnet
8.
properly. Severe injury
used properly and safely.
9. Do not expose the magnet
℉
(1760F). High temperatures
magnet's effectiveness
condition. Keep the square
from the welding point and remove after the tack weld.
10. Never use the square
lifting or to transport
The magnet is not recommended
11.
surfaces with paint or polish
the magnetic force.
12. Always keep the bottom
debris and rust. If needed,
SPECIFIC SAFETY
1. Always test the connection
square welding magnet
holding the material
Visit www.princessauto.com
Magnetic Welding
)
Magnetic
and Fabrication
110 lb.
Extremely powerful magnetic
welding squares that
you to turn the magnet
off with a twist of the
Allows for fast and exact
placement. Simply clean off
the magnet by turning
magnetic force.
all instructions
must follow basic
injury
warnings, precautions,
instructions.
safety goggles that provide
Eye protection
with CSA Z94.3-07
on the type of work performed.
protection based on the
was designed
Do not modify or alter this tool or
purpose.
electronics, credit cards,
welding magnet is stored
with ferromagnetic
and powerful attraction.
magnet to lift or transport
it is ideal for debris cleanup,
etc.
for normal work/jobsite
or in a
if it is damaged or is not working
can occur if this device
to temperatures above
will permanently degrade
and may result in an unsafe
welding magnet at least 3 in.
welding magnet for overhead
any materials.
for use on
as these will reduce
of the magnet clean and free of
wipe with some oil.
PRECAUTIONS
before attempting
to ensure that it is capable
securely.
for more information
and Fabrication
Welding
Square
User Manual
2. Numerous
the magnetic
painted
allow
the
on or
the connection
handle.
3. Thicker
metals. Example: 1/4 in. (6mm)
strongly
off the
the magnet to slide. Use of a backing
hold more
4. Never
magnet. The magnet
away
before
Avoid sudden jerking or shock force as this will cause
5.
the magnet
and/or
6. Threaded
magnet to mount accessories
operating into
ferromagnetic
unless using some spacers. This will keep the magnetic
front
grip
7. It is recommended
or ANSI
used
when used as a holder for your jig or fixture. Wood,
plastic
materials
Alternatively
between
This square
8.
used as a welding
etc.
electrical
in the
9. For safe operation,
must
possible
metals
sandpaper
would
10. As with all precision
nuts
dropping,
periodic
degree angles are still accurate
magnet
OPERATION
is not
This square
pipe, bar and rod stock,
℃
800C
greatest
the
that have "V" slots have very powerful
forces
degree
NOTE:
the square
hold of the bottom
more than
1. The handle
turned
be turned
the magnet
2. Do not turn
to use the
ferromagnetic
of
Square
factors can negatively
bond, like dirt, debris, oils and grease,
surfaces and any gap between
metal surface will decrease
point is clean
metals will be held more
than thin gauge metals.
securely when placed
exceed the rated capacity
has up to 110 lbs. (50 kg) of break-
force.
to lose its hold.
holes are provided
a fixture. For the best results
metals to the square welding
at its most powerful.
that stainless
to attach non-ferromagnetic
and aluminum are all non-ferromagnetic
that make for excellent
non-ferromagnetic
the square welding
welding magnet
ground clamp or as part of an
circuit.
the bottom
always be flat and smooth.
to sand the magnet
and a flat surface. Always file any burrs that
interfere with full contact.
devices, damage can occur from
bumping and impact.
inspection by the user to ensure
still fits their needs.
welding magnet is designed
flat stock
holding power is straight
as well. This allows the magnet
angles.
Attaching ferromagnetic
welding magnet will
as this force
one direction.
on the square welding
clockwise 180 degrees
ON. It is not possible
has been fully turned ON.
on unless the magnet
metals.
V4.O
affect the strength of
the magnet and
the bond. Ensure that
and free of these factors.
strongly than thinner
steel will be held more
Thin metals will allow
plate will help to
on this metals.
of the square welding
in this square welding
to it or mount the square
do not attach
magnet,
steel screws can be
materials to the sides
attachments.
spacers can be placed
magnet and the jig/fixture.
is not designed to be
surface of the magnet
If necessary, it is
face smooth using
We recommend
that the 90
and the square welding
to hold steel plate,
or angle iron. While the
at the base, the two sides
magnetic attraction
to create precise 90
metals to the sides of
reduce the magnetic
is now shared among
magnet must be
until it stops in order to
to hold it in place unless
is in contact with