PRO-POINT 8587974 Mode D'emploi
Les langues disponibles
Les langues disponibles
Vl.o
PRO.POINT
Pro Chain
Sharpener
INTRODUCTION
Sharpens
chain
right
on the bar.
Precise, professional
too that give an
accurate
and fast sharpening.
SAFETY
WARNING!
Read
and
understand
instructions
before
using
The operator
must
follow
precautions
to reduce the risk of
personal
injury and/or
damage
the
equipment.
Keep this manual for safety warnings,
precautions,
operating
or inspection
and
maintenance
instructions.
I.
Always wear gloves.
Visit
www.princessauto.com
2.
Always
working
3.
Make
guide
to the chainsaw
before
4.
Check components
guide regularly
general
WARNING!
for cutter
gauge
angles,
settings
gauges
chainsaw
result
operator
all
ASSEMBLY
this tool.
basic
When
number,
to
Parts
for
more
information
Pro Chain
Sharpener
work
on a clean, flat
surface.
certain
that
the
file
has been mounted
securely
guide bar
sharpening.
on the file
for wear and
condition.
Follow
all instructions
filing
angles
and depth
settings.
Incorrect
sharpening
excessive
depth
gauge
or incorrectly
shaped
depth
may increase
the risk of
kickback.
Kickback
can
in severe
injury
to the saw
or to bystanders.
this manual
refers
to a part
it refers
to the included
Breakdown.
1.
Select
the proper
file size for the
chain to be sharpened
(see Chain
Filing
Chart).
Insert
the file into the
chain-file
holder
(3) and secure
tightening
both locking thumb
screws
(4). See figure
1.
2.
Mount
the file guide
assembly
to the guide bar so that the chain
guide
T-bars
(5) are flush
top of the rivets. Tighten the
assembly
with
the locking
screw
(8). See figure
2.
3.
Position
the
back
of the
against
the chain
stop
(7). See figure
3. Secure
the T-bars
(5). Adjust
chain position
using the thumb
(6) and slotted
screw
(12). See
figure 3.
OPERATION
SET
CUTTER
ANGLES
1.
Set the tilt and swivel
either the "00" to "100" angle marks.
See chain
filing
chart
for proper
degree mark setting.
See figure 4.
Lock into place using the
swivel
knob
(9).
8587974
by
on
with the
thumb
cutter
the
screw
base (14) to
Manuels Connexes pour PRO-POINT 8587974
Sommaire des Matières pour PRO-POINT 8587974
- Page 1 Vl.o Pro Chain Sharpener 8587974 Always work on a clean, flat Select the proper file size for the chain to be sharpened (see Chain working surface. PRO.POINT Filing Chart). Insert the file into the Make certain that file chain-file holder...
- Page 2 8587974 Pro Chain Sharpener Vl.o Set the top guide swivel (2) and File all cutter from inside Move cutter backwards until lock into position with the swivel the outside. See figure 10. the file is directly above the depth knob (10).
- Page 3 Vl.o Pro Chain Sharpener 8587974 After each depth gauge has been Inspect the tool components PARTS filed to the recommended height, periodically. Repair or replace BREAKDOWN round front corner to the damaged or worn components. original shape by free-hand filing.
- Page 4 8587974 Vl.o FIGURES Fig.l Fig.6 Fig.ll FiB16 Fig. 17 Fig.12 Fig.2 Fig.13 Fig.7 Fig.19 Fig.8 Fig.4 Fig.l Fig.9 Fig. Fig.10...
- Page 5 Outil d'affütage pour chaine professionnel Vl.o 8587974 Conservez ce manuel qui contient ASSEMBLAGE avertissements de sécurité, PRO.POINT précautions, Ies instructions Lorsque ce manuel fait référence å un fonctionnement ou d'inspection numéro de piéce, il fait référence et d'entretien. répartition des piéces comprise.
- Page 6 Outil d'affütage pour chaine professionnel 8587974 Vl.o Réglez la hauteur de la lime en Pour affüter les outils de coupe UTILISATION tournant la vis de réglage de la du cöté opposé de la chaine, RÉGLEZ LES ANGLES profondeur (no II) de facon ce que déverrouillez...
- Page 7 Outil d'affütage pour chaine professionnel Vl.o 8587974 Déplacez l'outil de coupe vers Limez toujours les jauges MISE REBUT l'arriére jusqu'å ce que la lime se profondeur de facon ce que la lime trouve directement au-dessus de Ia se déplace de I'intérieur...
- Page 8 Outil d'affütage pour chaine professionnel 8587974 Vl.o TABLEAU DE L/MAGE DE LA CHAINE Code de la chaine Angles de limage Taille de lime Réglage de la recommandés jauge de profondeur 5/32 po S (91VG) -I .025 5/32 po H (33SL) .025...