Hoover HGO300 HYDRO Manuel D'utilisation page 6

6
Remote Control Setup
Open the battery compartment on the back of the remote control. Insert two AAA / LR03 batteries into
the battery compartment. [Fig. 4] 1DUGTXG VJG EQTTGEV RQNCTKV[  
Charging the battery
Switch on the vacuum robot with the On/Off switch on the bottom (
the charging station.
Press the on/ standby switch on the vacuum robot or the charging base button on the remote control
Fig. 4
and then immediately the charging station button. Make sure the robotic vacuum cleaner is moving to
the charging station. [Fig. 5]
NOTE: Make sure that the charging contacts of the robot vacuum cleaner and charging base are not
dirty. Clean the contacts if necessary.
It is normal for the charging base and vacuum cleaner to become warm during charging.
Remove the water tank before charging the robot vacuum cleaner.
9JGP VJG DCVVGT[ KU EJCTIKPI VJG QP UVCPFD[ UYKVEJ .'& CUJGU DNWG If the battery is charged, the
LED is on permanently. [Fig. 6]
LED indicator
LED COLOR
PEMANENTLY BLUE
BLUE FLASHING
Fig. 5
INDICATOR LIGHT OFF
PEMANENTLY RED
Battery
Over time the capacity of your robot battery will diminish and it will need to be replaced. A replacement
battery can be purchased from an approved Hoover retailer. Only use genuine Hoover spares and
accessories.
Removal and replacement
Fig. 6
Ensure the robot is switched OFF.
Locate the battery compartment cover on the underside of the robot and remove the two screws.
Remove the battery from the compartment and disconnect the connector.
4G V C PGY DCVVGT[ CPF TGEQPPGEV VJG EQPPGEVQT 2C[ CVVGPVKQP VQ EQTTGEV CNKIPOGPV QH VJG EQPPGEVQT
4G V VJG DCVVGT[ EQXGT CPF VJG VYQ UETGYU [Fig. 7]
USING YOUR ROBOT CLEANER
Fig. 7
Set Time
6Q WUG VJG VKOGT VJG TUV VKOG OWUV DG UGV QP VJG TGOQVG EQPVTQN [Fig. 8]
Press the time button.
Press the Left/Right buttons to select the current day.
Press the Play/Pause button to set the day.
6JG JQWTU YKNN VJGP UVCTV CUJKPI 2TGUU VJG 7R&QYP DWVVQPU VQ UGV VJG JQWT
Press the Left/Right buttons to select the minutes.
Press the Up/Down buttons to set the minutes.
Fig. 8
Press the Left/Right buttons to select the minutes.
Press the Up/Down buttons to set the minutes.
Press the Play/Pause button to set the time.
An audible signal is given from the robot signifying that the time has been set.
+H VJG CWFKDNG UKIPCN KU PQV IKXGP 2TGUU VJG #761
on the remote control.
Fig. 9
Power On
1. Press the ON/OFF power switch on the bottom robot. [Fig. 9]
2. Press the on/ standby button on the device or the start/ pause button on the remote control to start
the cleaning process. [Fig. 10]
In standby mode, the LED is off. To activate the vacuum robot press the on/ standby button on the
Fig. 10
device or the start/ pause button on the remote control.
When the battery level is low, the robot automatically returns to the charging station. [Fig. 11]
Fig. 11
 [Fig. 9] Set it down in front of
I
CONDITION
Battery is fully charged
During charging
Product is swithced off
Error
button on the robot, then press the time
* Certain Models Only ** May vary according to model
GB
button