Set-Up And Connection - Dennerle 160 Primus Notice D'emploi

Masquer les pouces Voir aussi pour 160 Primus:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 11
1-09588_3076_GA Mehrweg_Primus_Quantum_0915_Layout 1 29.09.2015 15:30 Seite 14
Hose connector
CO
hose
2
Diffusion slots
CO
collector
2
Waste gas vent
Longlife suction clip

2 Set-up and connection

2.1 Connect the pressure reducer
For Reusable 160 and 300: Place CO
Turn setting knob on the pressure reducer as far as it will go in di-
rection "- " (CO
supply shut off).
2
Connect pressure reducer to CO
is fitted correctly and that the sealing surfaces are clean Tighten
coupling ring finger-tight with 27mm spanner.
2.2 Connect solenoid valve (Special Edition only)
Cut a piece of approx. 50 cm in length from the CO
ensuring that the cut is straight.
Connect the pressure reducer and solenoid valve with the hose.
IMPORTANT: The arrow on the solenoid valve must point in the
CO
flow direction
2
Slide each end of the hose as far as they will go onto the hose
connectors and fix with coupling rings.
Primus: Secure hose with clip (to open, push the ends of the clip
apart at the side). µ
The solenoid valve can be secured on the base cabinet with the
aid of the holding bracket. ¸
Connect the solenoid valve to the time switch. The time switch is
used to cut off the CO
supply at night, as plants do not consume
2
any CO
during the night. Tip: Simply connect the solenoid valve
2
and lighting to the same time switch. ¹
Control states:
Power ON = solenoid valve open
Power OFF = solenoid valve closed
2.3 Fitting the check valve
Cut a piece of approx. 10 cm in length from the CO
ensuring that the cut is straight.
Connect the short hose to the entrance of the check valve, and the
long hose to the exit. Slide hoses as far as they will go onto the
hose connectors and fix with coupling rings.
IMPORTANT: The arrow on the check valve must point in the
CO
flow direction, i.e. from the CO
2
per)
Connect the short hose to the pressure reducer
solenoid valve (for Special Edition)
Primus: Secure hose with clip (to open, push the ends of the clip
apart at the side). µ
cylinder in stand.
2
cylinder. Ensure that the washer
2
hose,
2
hose,
2
source to the diffusor (Flip-
2
or the
and secure with coupling ring.
2.4 Connect CO
flipper
2
Rinse Flipper with warm tap water (no detergents ).
Moisten the hose connector slightly and fit the CO
Choose a spot in the aquarium which is as dark as possible (to
prevent algae growth) and where the water movement is good.
Fix Flipper in vertical position, at least 5 cm below the surface of
the water.
Your CO
fertilizer system is now ready for use.
2
3 Setting the amount of CO
3.1 The right amount of CO
2
For lush plant growth, Dennerle recommends a CO
aquarium of approx. 20 to 25 mg/l.
Levels of CO
above 30 mg/l are not necessary for healthy plant
2
growth and should be avoided, so as to ensure that fish and other
creatures living in the aquarium are not subjected to any unnecessary
stress. The CO
content can be determined by means of the CO
2
long-term test (see 4) or by measuring carbonate hardness and pH
value (see 4.7).
3.2 Setting the number of bubbles
The required number of bubbles is dependent on various factors, such
as the stock of plants, water movement and lighting intensity. The ap-
propriate CO
supply level thus requires to be determined individually
2
for the specific aquarium concerned.
Rule of thumb for the basic setting: Begin at approx.
10 bubbles per minute per 100 l of aquarium water, i.e. 2 x 10 = 20
bubbles per minute for a 200 l aquarium.
Adjust the CO
supply to the desired CO
2
over several days. Please note: The more vigorously the surface of
the water is set in motion, the more CO
aquarium again.
Slowly open the cylinder valve.
Quantum: The cylinder pressure manometer will now indicate
approx. 60 bar (at 20 °C).
Slowly turn the setting knob on the pressure reducer towards
" + "(approx. 1 complete turn) until the first bubbles issue from
the Flipper.
Special Edition: The solenoid valve must be open for this purpose.
The desired number of bubbles can be set by turning the setting
knob to " + " or " - ".
Please note: After adjusting the pressure reducer, there is
always a delay before the number of bubbles is altered
accordingly (the hose acts as a pressure buffer). The number of
bubbles should thus be set in small steps, always waiting a
couple of minutes until the new setting has stabilised.
supply hose.
2
(number of bubbles)
2
level in the
2
2
content in small steps spread
2
will be expelled from the
2
15

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

300 quantum600 quantum

Table des Matières