Spektrum™ Firma™ Smart 130A Brushless Esc (Spmxse1130) - Horizon Hobby Losi Hammer Rey Manuel D'utilisation

SPEKTRUM FIRMA
™
SPECIFICATIONS
Type Sensorless, SMART Throttle Compatible
Output 130A/760A
Function Forward/Brake–Forward/Brake Reverse
Input Voltage 7.4V–14.8V
BEC Output 6V/4A
Dimensions (LxWxH) 57.5mm x 46mm x 38mm
Weight 154 g
ESC LED STATUS
• No ESC LEDs will glow when there is no throttle input from the transmitter.
• The red ESC LED glows when there is any throttle input from the transmitter.
AUDIBLE WARNING TONES
1. Input Voltage: The ESC checks the in put voltage when it is powered ON. If a voltage
problem is detected, the ESC continuously sounds 2 beeps with a 1 second pause
(xx-xx-xx). Power OFF the ESC and ensure the connections are secure and that
the battery power is not too low for safe operation.
2. Radio Connection: The ESC checks radio signal input when it is powered ON.
If a problem is detected, the ESC continuously sounds 1 beep with a 2 second pause
(x--x--x). Power OFF the ESC and ensure the radio system is operating correctly.
NOTICE: Always disconnect the battery from the ESC after operating your vehicle. The ESC's
switch only controls power to the receiver and servos. The ESC will continue to draw current when
connected to the battery, resulting in possible damage to the battery through over discharge.
ESC FUNCTIONS AND MODES
The ESC includes programming options so you can adjust the way your vehicle performs.
Refer to the included settings table to adjust the ESC for your driving conditions.
ESC PROGRAMMING PROCEDURE
Programming is accomplished using the SET button on the ON/OFF switch or Digital Program
Box (SPMXCA200).
1. Connect a fully charged battery to the ESC.
2. Power ON the ESC using the ESC switch.
3. Hold the SET button for 1 second until the green LED blinks, then release the SET button
to enter programming mode.
PROGRAMMABLE ITEMS
1 Running Mode
2 Drag Brake Force
3 Low Voltage Cutoff
4 Punch (Level)
5 Max Brake Force
6 Max Reverse Force
7 Initial Brake
8 Neutral Range
9 Timing
10 Thermal Protection
11 Motor Rotation
12 Li-Po Cells
HAMMER REY ROCK RACER: 1:10 4WD RTR, AVC • INSTRUCTION MANUAL
®
SMART 130A BRUSHLESS ESC (SPMXSE1130)
™
PROGRAMMABLE VALUE
1
Forward w/ brake Forward/Reverse w/ brake
0%
None 2.6V/Cell
1
25%
25%
Drag Brake
6%
0.00º
Enable
Counterclockwise Clockwise
Auto Calculate
ESC CALIBRATION PROCEDURE
Complete the transmitter/receiver binding procedure prior to calibrating the ESC.
1. Set the transmitter throttle channel to 100% travel and center the throttle trim.
2. Connect a battery to the ESC battery lead.
3. Power on the transmitter.
4. Press and hold the SET button while turning on the ESC. Release the SET button when
the red LED begins to flash, indicating the ESC is in calibration mode. The ESC will enter
programming mode if the button is held for more than three seconds.
TIP: The red LED should be flashing when the ESC enters calibration mode. If the green LED
is flashing the ESC has entered programming mode. Power off the ESC and repeat step 4,
releasing the SET button when the red LED begins to flash.
5. With the transmitter throttle trigger at the neutral position, press and release the ESC SET
button. The red LED will stop flashing, the green LED will flash one time and the motor will
make a tone to indicate the neutral position has been accepted.
6. While holding the throttle trigger at the full throttle position, press and release the ESC SET
button. The green LED will flash twice and the motor will make two tones to indicate the full
throttle position has been accepted.
7. While holding the throttle trigger at the full brake position, press and release the SET button.
The green LED will flash three times and the motor will make three tones to indicate the full
brake position has been accepted.
The motor will operate normally after calibration is completed.
4. Press and release the SET button as needed to get to the desired menu option (the Green
LED will blink corresponding to the menu item number). Programming menu items 1
through 9 are accessible using the SET button on the ESC. Programming menu items 10 and
above are only accessible using the optional ESC programming card. Programming of menu
items 10 and 11 is only possible after firmware updates to the ESC programming card.
5. When at the desired menu item, hold the SET button for 3 seconds until the red LED blinks.
6. Press the SET button to move among the settings based on how many times the red LED
blinks (Refer to the table for more information).
7. Save the setting by holding the SET button for 3 seconds.
8. Power OFF the ESC switch and repeat the instructions above to change other settings.
TIP: If desired, the ESC programming can be returned to default settings
by powering ON the ESC and holding the SET button for 5 seconds.
2 3
Forward/Reverse
5% 10%
2.8V/Cell
2 3
50% 75%
50% 75%
0% 20%
9% 12%
3.75º 7.50º
2S 3S
4 5 6
20% 40% 60%
3.0V/Cell 3.2V/Cell 3.4V/Cell
4 5 6
100% Disabled
100%
40%
11.25º 15.00º 18.75º 22.50º
4S
EN
Default Settings
7 8 9
80% 100%
7 8 9
26.25º
7