Publicité
USING THE CONTROL PANEL
NOTE: Press the dial to START or STOP any program. Turn to select.
POWER
Press to power
BLENDSENSE™
the unit on and off.
Intelligent one-touch program that senses
your ingredients and blends to perfection.
MANUAL
Adjustable speed for
MODE (Pitcher and Processor Bowl only)
total blending control.
Preset processing program (CHOP) that
chops for you.
PROCESSING MODE PROGRAMS
CHOP: Pitcher and Processor Bowl only.
Smart preset program combines unique pausing patterns that chop for you.
Press MODE, then with CHOP selected, press START/STOP. The program will
automatically stop when complete. Press the dial again to stop the program sooner.
Does not work in conjunction with the BlendSense program or Manual programs.
NOTE: Number of seconds is displayed for the program's runtime.
MANUAL PROGRAMS
Go manual for total control of your blending speed and textures. Press MANUAL,
turn the dial to select your desired speed, then press START/STOP. When selected,
each speed runs continuously for 60 seconds. Press the dial again to stop the
program sooner. Manual programs do not work in conjunction with the BlendSense
program or Processing Mode programs.
NOTE: Once speed is selected, runtime will count up on the display in seconds.
ninjakitchen.ca
USING THE PITCHER
IMPORTANT:
• Review all warnings at the beginning of this Owner's Guide before proceeding.
• As a safety feature, if the pitcher and lid are not properly installed, the timer will display INSTALL
and the motor will be disabled. If this happens, repeat step 5 on this page.
WARNING:
loose and sharp and NOT locked in place. If using the pour spout, ensure the lid is fully locked onto the
blender pitcher. If pouring with the lid removed, carefully remove the Stacked Blade Assembly first,
PULSE
holding it by the shaft. Failure to do so will result in a risk of laceration.
Operates only when PULSE
is pressed. Use short presses
for short pulses and long
NOTE:
presses for long pulses.
• DO NOT add ingredients before completing installation of the Stacked Blade Assembly.
• If the Stacked Blade Assembly is not fully seated, you will not be able to install and lock the lid.
• The pitcher lid handle will not fold down unless it is attached to the pitcher.
• DO NOT process or grind dry ingredients.
• For best results, blend fresh leafy greens and herbs in the single-serve cup.
1
Plug in motor base and place on a clean, dry, level surface such as a
countertop or table.
2
Lower the pitcher onto the motor base. The handle should be aligned slightly
to the right and the pitcher should be oriented so the LOCK symbols are
visible on the motor base. Rotate the pitcher clockwise until it clicks into place.
3
Exercising care, grasp the Stacked Blade Assembly by the top of the shaft and
place it onto the drive gear inside the pitcher. Note that the blade assembly
will fit loosely onto the drive gear.
6a If using the BlendSense program, simply press the dial. The program will
automatically stop once complete. To stop the unit at any time, press the dial again.
6b If using a Processing Mode program, select MODE, then use the dial to select
your desired program. To start, press the dial. The program will automatically
stop once complete. To stop the unit at any time, press the dial again.
6c If using a Manual program, select MANUAL, then use the dial to select your
desired speed (LOW, MEDIUM, or HIGH). To start, press the dial. Once the
ingredients have reached your desired consistency, press the dial again or
wait 60 seconds for the unit to come to a complete stop on its own.
7
To remove the pitcher from the motor base, turn the pitcher counterclockwise and then lift up.
8b For thicker mixtures that cannot be emptied through the pour spout,
remove the lid and Stacked Blade Assembly before pouring. To remove
the lid, press the RELEASE button and lift the handle. To remove the
blade assembly, carefully grasp it by the top of the shaft and pull straight
up. The pitcher can then be emptied.
9 Turn the unit off by pressing the Power button. Unplug the unit when
finished. Refer to the Care & Maintenance section for cleaning and
storage instructions.
Ninja Detect™ Total Crushing® & Chopping Blades (Stacked Blade Assembly) are
4 Add ingredients to the pitcher. DO NOT add ingredients past the
MAX LIQUID line.
5
Place the lid on the pitcher. Press down on the handle until it clicks
into place. Once the lid is locked in place, press the Power button
to turn unit on. The BlendSense™ program will illuminate.
8a To pour out thinner mixtures, ensure the lid is
locked in place, then open the pour spout cap.
ninjakitchen.ca
Publicité
