Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
19. CHECK DAMAGED PARTS. Before further use
of the tool, a guard or other part that is dam-
aged should be carefully checked to determine
that it will operate properly and perform its
intended function - check for alignment of
moving parts, binding of moving parts, break-
age of parts, mounting, and any other condi-
tions that may affect its operation. A guard or
other part that is damaged should be properly
repaired or replaced.
20. DIRECTION OF FEED. Feed work into a blade
or cutter against the direction of rotation of the
blade or cutter only.
21. NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN POWER OFF. Do not leave tool until it
comes to a complete stop.
22. REPLACEMENT PARTS. When servicing, use
only identical replacement parts.
23. POLARIZED PLUGS. To reduce the risk of elec-
tric shock, this equipment has a polarized plug
(one blade is wider than the other). This plug
will fit in a polarized outlet only one way. If the
plug does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified
electrician to install the proper outlet. Do not
change the plug in any way.
Table 1: Minimum gage for cord
Ampere Rating
More Than
Not More Than
0
6
10
12
Additional safety rules
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adher-
ence to miter saw safety rules. If you use this tool
unsafely or incorrectly, you can suffer serious per-
sonal injury.
1.
Wear eye protection.
2.
Keep hands out of path of saw blade. Avoid
contact with any coasting blade. It can still
cause severe injury.
3.
Do not operate saw without guards in place.
Check blade guard for proper closing before
each use. Do not operate saw if blade guard
does not move freely and close instantly.
Never clamp or tie the blade guard into the
open position.
Do not perform any operation freehand. The
4.
workpiece must be secured firmly against the
turn base and guide fence with a vise during
all operations. Never use your hand to secure
the workpiece.
5.
Never reach around saw blade.
6.
Turn off tool and wait for saw blade to stop
before moving workpiece or changing
settings.
Volts
120V
220V - 240V
6
–
10
12
16
VOLTAGE WARNING: Before connecting the tool
to a power source (receptacle, outlet, etc.) be sure
the voltage supplied is the same as that specified
on the nameplate of the tool. A power source with
voltage greater than that specified for the tool can
result in SERIOUS INJURY to the user- as well as
damage to the tool. If in doubt, DO NOT PLUG IN
THE TOOL. Using a power source with voltage less
than the nameplate rating is harmful to the motor.
USE PROPER EXTENSION CORD. Make sure your
extension cord is in good condition. When using an
extension cord, be sure to use one heavy enough to
carry the current your product will draw. An under-
sized cord will cause a drop in line voltage resulting
in loss of power and overheating. Table 1 shows the
correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next
heavier gage. The smaller the gage number, the
heavier the cord.
Total length of cord in feet
25 ft.
50 ft.
50 ft.
100 ft.
AWG
18
16
18
16
16
16
14
12
Unplug tool before changing blade or
7.
servicing.
8.
Always secure all moving portions before
carrying the tool.
9.
Do not use the tool in the presence of flamma-
ble liquids or gases.
10. Check the blade carefully for cracks or damage
before operation. Replace cracked or damaged
blade immediately. Gum and wood pitch hard-
ened on blades slows saw and increases potential
for kickback. Keep blade clean by first removing
it from tool, then cleaning it with gum and pitch
remover, hot water or kerosene. Never use gaso-
line to clean blade.
11.
Use only flanges specified for this tool.
12. Be careful not to damage the arbor, flanges
(especially the installing surface) or bolt. Damage
to these parts could result in blade breakage.
13. Make sure that the turn base is properly
secured so it will not move during operation.
Use the holes in the base to fasten the saw to a
stable work platform or bench. NEVER use tool
where operator positioning would be awkward.
14. For your safety, remove the chips, small
pieces, etc. from the table top before
operation.
3 ENGLISH
100 ft.
150 ft.
200 ft.
300 ft.
16
14
14
12
14
12
Not Recommended
Publicité
Table des Matières
