Publicité
• Pulse lighting of all LEDs - signals the exhaustion of the battery
and the need to recharge it.
• Flashing light of 2 LEDs - signals a partial discharge.
• 1 LED flashing light - indicates a high battery level.
After the battery is fully charged, the LED (12) on the charger lights
up green and all the battery charge status LEDs (15) glow
continuously. After some time (approx. 15 seconds), the battery
charge status LEDs (15) go out.
The battery should not be charged for more than 8 hours. Exceeding
this time may damage the battery cells. The charger will not turn off
automatically when the battery is fully charged. The green LED on
the charger will remain on. The battery charge status LEDs go out
after a while. Disconnect the power supply before removing the
battery from the charger socket. Avoid successive short recharges.
Do not recharge the batteries after using the device for a short time.
A significant decrease in the time between the necessary recharges
indicates that the battery is worn out and should be replaced.
The batteries heat up during the charging process. Do not start work
immediately after charging - wait for the battery to reach room
temperature. This will prevent damage to the battery.
SIGNALING THE STATE OF BATTERY CHARGE
The battery is equipped with battery charge status indicator (3
LEDs) (15). To check the battery charge status, press the battery
charge status indicator button (14) (Fig. C). All the LEDs light up to
indicate that the battery is high. Two LEDs on indicate partial
discharge. Only 1 LED flashes means the battery is empty and
needs to be recharged.
FASTENING THE SAW BLADE
The assembly and replacement of the saw blade is carried out
without the use of tools.
• Move the saw blade lock lever to the unlock position.
• Push the saw blade into the tool hole as far as it will go.
• Move the lock lever to the lock position.
• Check that the blade is properly seated in the holder by lightly
pulling the blade.
Use the correct saw blades for the intended work..
OPERATION / SETTINGS
ON / OFF
The device is equipped with a switch lock button (9) to prevent
accidental activation. The safety button is located on both sides of
the device casing (fig. F).
Enable:
• Press one end of the switch lock button (9) in and hold it in this
position.
• Press the switch button (8) (fig. G).
• After starting the device, the switch lock button (9) can be
released.
Switching off:
• Releasing the pressure on the switch button (8) stops the device.
The operating speed range of the device is regulated by the degree
of pressure on the switch button.
CUTTING
• Place the front part of the foot (2) flat on the material to be cut
without the blade touching the material.
• Start the saw and adjust the working speed to the properties of
the material to be cut.
• Move the saw blade slowly along the previously marked cutting
line (fig. H, I)
The cut should be made evenly, taking care not to overload the saw.
Excessive pressure on the saw blade will act as a brake, which will
adversely affect the cutting performance.
During work, the entire surface of the foot should adhere to the
surface of the material being processed.
Check that the working tool is correctly attached. Incorrectly or
inaccurately fitted tools may slip during operation and pose a risk to
the operator.
CHANGING THE COLLECTION MODE
• The saw is equipped with a pick-up function for convenient cutting
of soft materials. The function is activated by changing the position
of the pick-up switch (7) from "OFF" to "ON".
FIXING / CHANGING THE FOOT
• The foot position can be adjusted if required. To do this, push the
foot release lever (5) forward. Then it is possible to change its
position or remove. To lock the foot back, return the lever to its
original position.
CARE AND MAINTENANCE
Before
performing
any
maintenance activities, remove the battery from the device.
MAINTENANCE AND STORAGE
• It is recommended to clean the device immediately after each use.
• Do not use water or other liquids for cleaning.
• Clean the device with a dry cloth or blow it out with low pressure
compressed air.
• Do not use any cleaning agents or solvents as these may damage
the plastic parts.
• Regularly clean the ventilation slots in the motor housing to
prevent overheating of the device.
• Always store the device in a dry place out of the reach of children.
• Store the device with the battery removed.
All kinds of faults should be removed by the manufacturer's
authorized service.
TECHNICAL PARAMETERS
RATED DATA
Cordless reciprocating saw 58G096
Parameter
Supply voltage
The number of oscillations at idle
Working tool clamping system
Blade stroke
Maximum thickness of the material
to be cut
Protection class
Mass
Year of production
5G096 stands for both the type and designation of the machine
NOISE AND VIBRATION DATA
Sound
pressure
(grinding)
Sound power level (grinding)
Vibration acceleration value
(main handle)
Vibration acceleration value
(auxiliary handle)
Information regarding noise and vibration
The level of noise emitted by the device is described by: the level of
the emitted sound pressure L
(where K is the measurement uncertainty). The vibrations emitted
by the device are described by the value of the vibration
acceleration ah (where K is the measurement uncertainty).
The emitted sound pressure level L
the value of vibration acceleration ah given in this manual were
measured in accordance with EN 62841-1. The stated vibration
level ah can be used for the comparison of devices and for the initial
assessment of vibration exposure.
The stated vibration level is representative only for the basic use of
the device. If the machine is used for different applications or with
different work tools, the vibration level may change. The higher
vibration level will be influenced by inadequate or too seldom
maintenance of the device. The reasons given above may result in
an increased exposure to vibration during the entire period of
operation.
7
installation,
adjustment,
Value
18 V DC
0-3100 min
without tool
28 mm
(wood)
120 mm
(steel)
10 mm
3,4 kg
2021
level
Lp
= 79,0 dB(A) K= 5 dB(A)
A
Lw
= 90,0 dB(A) K= 5 dB(A)
A
2
a
= 8,20 m/s
K= 1,5 m/s
h
2
a
= 6,21 m/s
K= 1,5 m/s
h
and the sound power level L
pA
, sound power level LwA and
pA
repair
or
-1
III
2
2
wA
Publicité
