Publicité
•
Has the ice melted around the auger (metal spiral) in the
ice bin? Empty the ice container. Use warm water to melt the
ice if necessary.
Cut Hazard
Use a sturdy glass when dispensing ice.
Failure to do so can result
in cuts.
Is the ice dispenser stalling while dispensing "crushed"
ice? Change the ice button from "crushed" to "cubed." If
cubed ice dispenses correctly, depress the button for
"crushed"
ice and begin dispensing again.
•
Has the dispenser arm been held in too long? Ice will stop
dispensing when the arm is held in too long. Wait 3 minutes
for dispenser motor to reset before using again.
The water dispenser
will not operate
properly
•
Freezer door closed completely? Close the door firmly. If it
does not close completely, see "The doors will not close
completely."
•
Refrigerator connected to a water supply and the supply
shutoff valve turned on? Connect refrigerator to water
supply and turn water shutoff valve fully open.
•
Is the water pressure at least 30 psi (207 kPa)? The water
pressure to the home determines the flow from the dispenser.
See "Water Supply Requirements."
•
Kink in the home water source line? Straighten the water
source line.
•
New installation? Flush and fill the water system.
•
Water filter installed on the refrigerator? The filter may be
clogged or incorrectly installed.
•
Is a reverse osmosis water filtration
system connected to
your cold water supply? See "Water Supply Requirements"
in either the Installation Instructions or the Use & Care Guide.
Water is leaking from the dispenser
NOTE: One or two drops of water after dispensing
is normal.
•
Glass not being held under the dispenser long enough?
Hold the glass under the dispenser 2 to 3 seconds after
releasing the dispenser lever.
•
New installation?
Flush the water system. See "Prepare the
Water System" or "Water and Ice Dispensers."
•
Recently changed water filter? Flush the water system. See
"Prepare the Water System" or "Water and Ice Dispensers."
The dispenser
water is not cool enough
NOTE: Water from the dispenser is chilled to only 50°F (10°C).
•
New installation?
Allow 24 hours after installation for the
water supply to cool completely.
•
Recently
dispensed
large amount of water? Allow
24 hours for water supply to cool completely.
•
Water not been recently dispensed?
The first glass of water
may not be cool. Discard the first glass of water.
•
Refrigerator
connected
to a cold water pipe? Make sure
the refrigerator is connected to a cold water pipe. See "Water
Supply Requirements."
ACCESSORIES
To order replacement filters, call 1-800-442-9991
and ask for the
appropriate
part number listed below or contact your authorized
Whirlpool dealer. In Canada, call 1-800-807-6777.
Stainless Steel Cleaner and Polish:
Order Part #4396095
Standard
Filter:
Order Part #4396841 (T2RFWG2)
In Canada, Order Part #4396841 B (T2RFWG2)
WATER FILTER CERTIFICATIONS
Tr adenlar k/?_led_d
Designation
Whlrll_)OI
DcIuxe
'I'l WC}2
WhlrluooI
DcluxeT]
WG2L
State
of Cahfornm
Department
of Health
Services
Water Trealment Device
Certificate Number
()5
-
1702
I)ate I_l_ed:
April 6, 2{g15
_me R_,v)sed
_eotemtx,r
7. 200_
Rerdacement
ElemeRts
T2RFWG2
Rated
Service
Capacity:
2(_) ga]s
Rated
Service
Flow:
0 5 gpm
Conditions
of Certificatioa:
Do _ot use with wa_eT tha_ is microbiological/y
u_sa_
or of nnkno_ n quality,
without
adequam
disinfcclion
beam
or
after t_ sys_m
11
Publicité
