Bestway FAST SET 57448 Manuel D'utilisation page 6

SETUP INSTRUCTIONS
Overview
Choosing the Correct Location:
The location chosen where the pool will be installed must respect the following conditions:
- Because of the combined weight of the water inside the pool and the users, it is extremely important that the surface chosen is
capable of uniformly supporting the total weight for the entire time the pool is installed. When choosing the surface, take into
consideration that water may come out of the pool when in use or when it rains. If the water softens the surface, it may lose its
capability to support the pool weight.
- The surface must be flat and smooth. If the surface is inclined or uneven, it can create an unbalanced load on the structure of the
pool. This can damage the welding points of the liner and bend the frame. In the worst cases, the pool can collapse, causing serious
personal injury and/or damage to personal property.
- We recommend positioning the pool away from any objects children could use to climb into the pool.
- Position the pool near an adequate drainage system to deal with overflow or to empty the pool. Ensure the pool side with the water
inlet A and outlet B is facing in the direction of the power source, where the filtration system will be connected.
- The selected surface must be clear of any type of object. Due to the weight of the water, any object under the pool could damage
or perforate the bottom of the pool.
- The selected surface must be clear of aggressive plants and weed species. Types of strong vegetation could grow through the liner and
create water leakage. Grass or other vegetation that may cause odor or slime to develop must be eliminated from the chosen location.
- The selected location must not have overhead power lines or trees. Be sure the location does not contain underground utility pipes,
lines or cables of any kind.
- The selected position must be far from house entrance. Do not position any equipment or other furniture around the pool. The water
that comes out of the pool during use or due to product malfunctions can damage furniture inside the house or surrounding the pool.
- The selected surface must be flat and without holes that can damage the material of the liner.
Suggested surfaces: grass, ground, concrete and all other surfaces that respect the above set-up conditions.
Surfaces to avoid: mud, sand, gravel, deck, balcony, driveway, platform, soft/loose soil or other surface that does not meet the
above set-up conditions.
Follow the important instructions above to choose the correct surface and location to set up your pool. If parts become damaged
because the set-up surface and location does not adhere to these instructions, it will not be considered a manufacturer defect and will
void the warranty and any service claims.
Additional Guidelines:
Check with your local city council for bylaws relating to fencing, barriers, lighting and safety requirements, and ensure you comply
with all laws.
If a pump and/or ladder is included in the set, refer to the pump's and/or ladder's manual for safety instructions and installation. The
ladder must match the pool size.
If you must change locations during set-up, lift the liner to move it; do not drag it on the ground. The friction between the PVC material
and the ground can damage the pool liner.
Parts & Tools Needed
Compare the parts in your box to the parts listed in this manual.
Verify that the equipment components represent the model that you had intended to purchase. If any parts are damaged or missing at
the time of purchase, visit our website bestwaycorp.com/support.
Assembly Instructions
For installation instructions, scan the QR code printed on the front cover or follow the illustrations inside the manual.
are for illustration purposes only. May not reflect actual product. Not to scale.
Assembly of this pool can be completed without additional tools. Installation takes approximately 10-15 minutes with 2-3 people,
excluding any preparations or water filling (refer to the package for specific information about your purchased item). Please note that
assembly times may vary based on pool size and individual experience.
Bestway is not responsible for damage caused to the pool due to mishandling or failure to follow these instructions.
Inflation Instructions:
Inflate the top ring carefully; it is recommended to use low pressure electrical pump or hand pump to inflate the top ring.
When the top ring reaches the correct pressure, it should be slightly stiff to the touch. Over-inflating the top ring can cause permanent
deformation or damages, due to the high elasticity of the PVC material.
To increase the lifespan of the top ring, we recommend to add air as few times as possible during the season. If the top ring becomes
soft, wait until sunset to re-inflate until it is slightly stiff to the touch.
Helpful Installation Tips:
We strongly suggest opening the package and assembling the pool when the ambient temperature is above 15ºC / 59ºF. The PVC
material of the liner will be more flexible and easier to assemble in this environment.
We suggest you buy a pool ladder (if one is not included in the set) and prepare it before setting up the pool, as it will help whenever
you need to get inside it.
Step 2: When the pool is filled with around 1 cm (0.39'') of water, gently smooth out the bottom liner to remove all folds. We recommend
starting from the center of the pool and continuing outwards. You can continue to fill the pool when the floor is smooth and wrinkle-free.
Filling the Pool with Water:
ATTENTION: Do not leave the pool unattended while filling with water. Continuously check the pool to ensure it is being filled correctly.
It is highly recommended to use tap water for filling to minimize unwanted content, such as minerals. Do not use sea water.
Fill the pool with water after all assembly steps are completed. The pool is full when the water reaches the welding line (under the
inflated top ring as shown in Step 5).
IMPORTANT: When reaching the proper water level, check that the distance between the water surface and the top ring is the same
all around. If it is different, it means that the surface is not level, and we strongly recommend draining the water and adjusting the
chosen location. Never attempt to move the pool with water still in it.
IMPORTANT: Keeping the pool full of water on unlevel ground can cause the bursting of welding points and/or pool collapse, causing
serious personal injury and/or damage to property. Do not overfill as this could cause the pool to collapse. In the case of heavy
6
Drawings