Description; Safety; Cleaning And Maintenance - Vortice VORT QBK Notice D'emploi Et D'entretien

ENGLISH

Description

The product you have purchased is a high tech
industrial centrifugal extraction fan.

Safety

Warning:
!
this symbol indicated the need to
take precautions to prevent the user from harm
• Do not use this appliance for functions other than
those described in this booklet.
• After removing the appliance from its packaging,
ensure that it is complete and undamaged. Check
that:
- the fan blades can rotate freely;
- the flexible supports are undamaged;
- the external panel shows no signs of damage;
- there are no foreign bodies inside the product;
- internal parts with direct access are clean.
If in doubt contact an authorised Vortice service
centre. Do not leave packaging within the reach of
children or differently able persons.
• Certain fundamental rules must be observed when
using any electrical appliance:
- never touch appliances with wet or damp hands;
- never touch appliances while barefoot;
- do not allow the unit to be operated by
unsupervised children or disabled persons.
• Store the appliance out of the reach of children and
disabled persons if you decide to disconnect it from
the power supply and use it no more.
• Do not us the appliance where there are
inflammable substances and vapours (alcohol,
insecticides, petrol, etc.).
• Do not use in potentially explosive environments.
• The interior of the appliance must only be cleaned
by trained personnel.
• If this appliance is to be installed in a location where
can be constantly subjected to noise, appropriate
sound-proofing measures must be taken or personal
protection equipment issued.
This appliance can be used by
•
children no less than 8 years of
age and by individuals with
limited physical, sensory or
mental capacities,
inexperienced
individuals, provided that they
are supervised or have been
instructed in safe use of the
appliance and understand the
associated risks. Children must
not play with the appliance.
Cleaning and
12
or by
or untrained
maintenance
procedures
undertaken by the user must not
be entrusted to children, unless
under supervision.
Caution:
!
this symbol indicates that care must
be taken to avoid damaging the appliance
• Do not make modifications of any kind to this
appliance.
• Regularly inspect the appliance for visible defects. If
the appliance does not function correctly, do not use
it and contact an authorised Vortice service centre
immediately
• If the appliance malfunctions and/or develops a fault,
contact Vortice immediately.
genuine original Vortice spares are used for any
repairs.
• Should the appliance be dropped or suffer a heavy
blow, have it checked immediately by Vortice.
• The appliance must be installed by a professionally
qualified technician
• The mains power supply to which the units are
connected must comply with current laws.
• The appliance must be connected to an efficient
earthing system.
• The electrical power supply/socket to which the
appliance is to be connected must be able to provide
the maximum electrical power required by the
appliance. If it cannot do so, arrange for a qualified
electrician to make the necessary modifications.
• The power supply system must be fitted with a
thermomagnetic or suitably sized differential switch
with a contact aperture of at least 3mm.
• The temperature of the air being treated on intake
must not be outside the range specified for the
appliance.
• Keep the appliance intake and outlet grilles free to
ensure the best possible flow of air.
• Always protect the appliance with a safety grille to
prevent contact with the fan blades and stop foreign
bodies from entering the appliance
• The appliance must be mounted on suitably sized
supports and is not suitable for bearing the weight of
ducting connected to it.
• If the appliance has to be stored outside before
installation, make sure that it is well protected from
the elements to prevent damage from rain, foreign
bodies or dirt.
The appliance must be installed
•
by a professionally qualified
electrician.
The appliance must be wired to
•
the power supply by way of a
multi-pole isolating switch with a
gap of at least 3 mm between
contacts.
that can
Ensure that only
be