How To Assemble - kikkaride AXES Mode D'emploi

WARNING: Like any other moving products, scooter riding can be a hazardous activity and may be dangerous. Be sure to read the entire manual before
riding and keep the manual permanently. In particular, pay attention to the following notices.
• Protective equipment should be worn: helmets, elbow pads, kneepads, long sleeve shirt, gloves, long pants. Not to be used in traffic. 50kgs max.
• Do not add any load on the handlebar as it may affect the product stability.
• Check the limitations for use in accordance with local road regulation. For private use only, and it is not a toy. Never ride in traffic, on the road or on the
pavement and watch your surroundings for pedestrians, bikes, skateboarders and scooter riders.
• Only ride on smooth and level paved surface. DO NOT ride at dust or at night when vision may be impaired. DO NOT ride your scooter down hills, near
steps or waterways.
• Do not use the scooter in wet weather. Never ride on it through water, and never immerse it in water; electrical and drive could be damaged by water
or create other possible unsafe conditions.
• All children and preteens should ride with adult supervision at all times.
• If the handlebar is unaligned, this may be a sign that it is not securely fastened. Please align the wheels with handlebar and then tighten the bolts of
"C" Clamp. This check should be undertaken every time you ride.
• Do not touch the motor or the brake when in use or directly after use as it can become very hot.
• Braking distances are increased in rainy weather or when wheels are wet.
• Keep your finger and other body parts away from the motor, wheels and all other moving components.
• Only use the battery specified by the manufacturer.
• Only use the charger specified by the manufacturer.
• Do not make any modifications the scooter
• Never allow more than one person at a time to ride the scooter.
• LITHIUM BATTERY CONTAINS DANGEROUS ARTICLES. SHIP LITHIUM ONLY ACCORDING TO LOCAL LAW.
This scooter complies with:
EN14619 Safety Requirement for Roller Sports
2011/65/EU RoHS directive
EN 55014-1:2017 Requirements for household appliance, electric tools and similar apparatus---Part 1: Emission ,
EN 55014-2:2015 Requirements for household appliance, electric tools and similar apparatus---Part 2: Immunity – Product family standard.
EN 61000-6-3:2007+A1:2011+AC:2012 Electromagnetic compatibility (EMC). Generic standards. Emission standard for residential, commercial and
light-industrial environments
EN 61000-6-1:2007. Electromagnetic compatibility (EMC). Generic standards. Immunity for residential, commercial and light-industrial environments
EN 61000-3-2:2014 Electromagnetic compatibility (EMC). Limits. Limits for harmonic current emissions
EN 61000-3-3 :2013 Electromagnetic compatibility (EMC). Limits. Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage
supply systems, for equipment with rated current ≤ 16 A per phase and not subject to conditional connection
EN 60335-1:2012+A11:2014+A13:2017. Household and similar electrical appliances. Safety. General requirements
EN 60335-2-29:2004+A2:2010 Safety of household and similar electrical appliances, Particular requirements for battery charger
Directive 2006/42/EC Annex I Essential health and safety requirements relating to the design and construction of machinery.

1. HOW TO ASSEMBLE

Parts( Figure 1)
1.Top Clamp; 2. Handlebar; 3.Stem; 4 'C'Clamp; 5. threaded tube; 6. G Sensor; 7. Brake pad; 8. Rear hub motor; 9. Charging port; 10. On/Off
swit ch; 11. Battery charger(included);12. 5mm hex wewnch (included)
Step1: Insert the Stem onto the Threaded Tube.
Step 2: Screw out the Top Clamp, place the handlebar set onto the top of stem, put the Top Clamp onto handlebar(Note: Align the raised point into the
hole of handlebar), screw in the bolts and then tighten them completely.
Step 3: Align the handlebar with the front wheel; then tighten the bolt of "C" Clamp with the supplied Allen Key.
ENGLISH