Electrical Safety; Residual Risks - Lux Tools A-Rm-46-24 Set Notice Originale

GB
– Maintain the device in accordance with
the instructions in the operating instruc-
tions.
– Avoid working at low temperatures.
– When it is cold, make sure your body and
your hands, in particular, are kept warm.
– Take regular breaks and move your hands
at the same time to promote circulation.
Electrical safety
• Power tool plugs must match the out-
let. Never modify the plug in any way.
Do not use any adapter plugs with
earthed (grounded) power tools.
Unmodified plugs and matching outlets
will reduce risk of electric shock.
• Avoid body contact with earthed or
grounded surfaces, such as pipes,
radiators, ranges and refrigerators.
There is an increased risk of electric
shock if your body is earthed or grounded.
• Do not expose power tools to rain or
wet conditions. Water entering a power
tool will increase the risk of electric shock.
• Do not abuse the cord. Never use the
cord for carrying, pulling or unplug-
ging the power tool. Keep cord away
from heat, oil, sharp edges or moving
parts. Damaged or entangled cords
increase the risk of electric shock.
• When operating a power tool outdoors,
use an extension cord suitable for out-
door use. Use of a cord suitable for out-
door use reduces the risk of electric
shock.
• If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected sup-
ply. Use of an RCD reduces the risk of
electric shock.
Personal safety
• Stay alert, watch what you are doing
and use common sense when operat-
ing a power tool. Do not use a power
tool while you are tired or under the
influence of drugs, alcohol or medica-
tion. A moment of inattention while oper-
ating power tools may result in serious
personal injury.
• Use personal protective equipment.
Always wear eye protection. Protec-
tive equipment such as dust mask, non-
skid safety shoes, hard hat, or hearing
protection used for appropriate conditions
will reduce personal injuries.
42
• Prevent unintentional starting. Ensure
the switch is in the off-position before
connecting to power source and/or
battery pack, picking up or carrying the
tool. Carrying power tools with your finger
on the switch or energising power tools
that have the switch on invites accidents.
• Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotating
part of the power tool may result in per-
sonal injury.
• Do not overreach. Keep proper footing
and balance at all times. This enables
better control of the power tool in unex-
pected situations.
• Dress properly. Do not wear loose
clothing or jewellery. Keep your hair
and clothing away from moving parts.
Loose clothes, jewellery or long hair can
be caught in moving parts.
• If devices are provided for the connec-
tion of dust extraction and collection
facilities, ensure these are connected
and properly used. Use of dust collec-
tion can reduce dust-related hazards.
• Do not let familiarity gained from fre-
quent use of tools allow you to become
complacent and ignore tool safety
principles. A careless action can cause
severe injury within a fraction of a second.
Service
• Have your power tool serviced by a
qualified repair person using only
identical replacement parts. This will
ensure that the safety of the power tool is
maintained.
• Never service damaged battery packs.
Service of battery packs should only be
performed by the manufacturer or author-
ized service providers.
Residual risks
• Even if you are operating this product in
accordance with all the safety require-
ments, potential risks of injury and dam-
age remain. The following dangers can
arise in connection with the structure and
design of this product:
• Health defects resulting from vibration
emission if the product is being used over
long periods of time or not adequately
managed and properly maintained.
• Injuries and damage to property due to
broken cutting attachments or the sudden
impact of hidden objects during use.