Noise/Vibration Information; Battery Charging - Bosch GWS 18V-10 Professional Notice Originale

10 | English
Angle grinder
Rated voltage
A)
Rated speed
No-load speed
Max. grinding disc diameter
Grinding spindle thread
Max. thread length of grinding spindle
Kickback stop
Restart protection
Run-out brake
Speed preselection
Weight according to EPTA-Procedure 01:2014
– with additional low-vibration auxiliary handle
– with standard auxiliary handle
Recommended ambient temperature during
charging
Permitted ambient temperature during opera-
B)
tion and during storage
Recommended batteries
Recommended chargers
A) Depends on battery in use
B) Limited performance at temperatures <0 °C

Noise/Vibration Information

Noise emission values determined according to
EN 60745-2-3.
Typically, the A-weighted sound pressure level of the power
tool is 79 dB(A). Uncertainty K = 3 dB. The noise level when
working can exceed the volume stated. Wear hearing pro-
tection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-3:
Surface grinding (roughing):
2 2
a =6.5 m/s , K=1.5 m/s ,
h
Grinding with abrasive disc:
2 2
a =3.5 m/s , K=1.5 m/s .
h
The vibration level given in these instructions has been
measured in accordance with a standardised measuring pro-
cedure and may be used to compare power tools. It can also
be used for a preliminary estimation of exposure to vibra-
tion.
The stated vibration level applies to the main applications of
the power tool. However, if the power tool is used for differ-
ent applications, with different application tools or poorly
maintained, the vibration level may differ. This can signific-
antly increase the exposure to vibration over the total work-
ing period.
To estimate the exposure to vibration accurately, the times
when the tool is switched off or when it is running but not ac-
1 609 92A 51Z | (13.09.2019)
GWS 18V-10
V=
-1
min 9000
-1
min
mm
mm
A)
kg 2.6-2.8
kg 2.4-2.6
°C 0 to +35
°C –20 to +50
GBA 18V...
ProCORE18V...
GAL 18...
GAX 18...
GAL 36...
tually being used should also be taken into account. This can
significantly reduce the exposure to vibration over the total
working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping the hands warm,
and organising workflows correctly.
Fitting

Battery Charging

Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
GWS 18V-10 GWS 18V-10
18 18
9000
– –
100 115
M 10 M 14
22 22
● ●
● ●
● ●
– –
2.6-2.8
2.4-2.6
0 to +35
–20 to +50
GBA 18V...
ProCORE18V... ProCORE18V...
GAL 18...
GAX 18...
GAL 36...
Bosch Power Tools
18
9000
–
125
M 14
22
●
●
●
–
2.6-2.8
2.4-2.6
0 to +35
–20 to +50
GBA 18V...
GAL 18...
GAX 18...
GAL 36...