Optional Accessories - Kreg Jig K4 Guide D'utilisation

9
Joining ½" -thick stock
(13mm)
When using the optional Micro-Pocket
TM
drill bit with ½" (13mm)-thick stock, set the drill guide at
the ½" mark. Position the drill-bit stop collar for
material. Join the parts with Kreg SPS-F075 screws. The
small-diameter head of these ¾" (19mm) panhead screws
seats below the workpiece surface to allow plugging with
a Micro pocket-hole plug. The ⁄ " stop-collar setting provides
5
8
maximum screw engagement in the mating workpiece.
Common Board Sizes
Nominal Size
1x2
1x3
1x4
1x6
1x8
2x2
2x4
2x6
2x8
4x4
6x6
6 Tips to Reduce Wood Splitting
1 Test Pieces
Test the joint with scrap pieces cut from the same stock as your final workpiece.
2 Make sure you're using Kreg Screws
Kreg screws feature sharp, self-tapping tips that slice through the wood fibres.
3
Use the Right Screw Type
Use fine-thread screws in hardwood. These #7 screws displace less wood than the #8 coarse-
thread screws that are used for softwood, plywood, MDF and particleboard.
4 Drive Progressively
Drive the screw halfway in, back it out to clear excess wood fibres from the hole, and then drive
the screw all the way in.
Reduce Friction
5
Apply beeswax or other lubricant to the screw to reduce the friction as the screw enters the
workpiece.
6 Clamp Correctly
Centre the clamp pad on the joint line to apply equal pressure to both workpieces and keep
them from shifting. Firm clamping pressure forces the screw to slice through the wood instead
of splitting it apart.
Tips
Drill Guide and
⁄ "-thick
5
8
Actual Size
⁄ " x 1 ⁄ "
3 1
4 2
3 ⁄ " x 2 1 ⁄ "
4 2
3 ⁄ " x 3 1 ⁄ "
4 2
3 ⁄ " x 5 1 ⁄ "
4 2
⁄ " x 7 ⁄ "
3 1
4 4
1 1 ⁄ " x 1 1 ⁄ "
2 2
1 1 ⁄ " x 3 1 ⁄ "
2 2
1 1 ⁄ " x 5 1 ⁄ "
2 2
1 ⁄ " x 7 ⁄ "
1 1
2 4
3 1 ⁄ " x 3 1 ⁄ "
2 2
5 1 ⁄ " x 5 1 ⁄ "
2 2

Optional Accessories

Available from your Kreg dealer or online at kregtool.com
Micro-Pocket Drill Guide
™
With a hole diameter 25% smaller than our standard pocket hole,
the Micro-Pocket Drill Guide lets you create compact pocket
™
holes in small projects, thin stock, and tight repair applications.
Kreg Jig ® HD
Designed for use with 1½" (38mm)-thick and thicker framing
material, this heavy-duty system features 14 x 2½" (64mm)
pocket screws.
Quick Change Kit
Switch from drilling pocket holes to driving pocket-hole screws
in seconds. The quick-change chuck installs in any three-jaw
drill chuck to accept standard ¼" (6mm) hex-shank bits.
Mini-Trak 48"
(1219 mm)
Enhance the utility of the workpiece support stop included with
the K4MS by mounting a piece of this T-track on both sides of
your bench-mounted jig. Anchoring the support stop to the T-track
allows for easy repositioning.
Kreg Clamps
Set the desired pressure and these clamps automatically adjust
to any material thickness up to 2
reach clamp and 4½" (108mm) for the 6" (152mm)-reach clamp.
Kreg System Organiser
Keep your entire pocket-hole workshop in this compact, fitted case.
Accommodates K3, K4 or K5 pocket-hole jigs, face clamps, Micro,
HD and plug cutter drill-guide blocks, drill and driver bits, and an
assortment of pocket screws.
10
⁄ " (73mm) for the 3" (76mm)-
7
8