English; General Safety Instructions; Product Description And Specifications; Product Features - Bosch GTA 2500 W Professional Notice Originale

12 | English

English
Safety Instructions

General Safety Instructions

Read all the warnings and instructions in-
cluded with the saw stand or the power tool
you intend to mount on it. Failure to observe
the safety information and follow instructions
may result in electric shock, fire and/or serious
injury.
Safety Instructions for Saw Stands
Disconnect the plug from the power source and/or re-
u
move the battery from the power tool before making
any adjustments to the power tool or changing ac-
cessories. Accidents can occur when power tools are
started unintentionally.
Assemble the saw stand properly before mounting the
u
power tool. Correct assembly is important to prevent the
risk of collapsing.
Firmly secure the power tool to the saw stand before
u
using it. You may lose control of the power tool if it slips
on the saw stand.
Place the saw stand on a firm, flat, horizontal surface.
u
If there is a chance that the saw stand will slip or wobble,
the safe and steady machining of the workpiece cannot
be guaranteed.
Do not overload the saw stand or climb or stand on it.
u
Overloading or standing on the saw stand can raise its
centre of gravity, causing it to tip over.
Ensure that all screws and connecting pieces are
u
tightly fastened during transport and when carrying
out work. Loose connections can cause instability and in-
accurate sawing.
Only install and remove the power tool when it is in
u
the transport position (for information on the trans-
port position, also refer to the operating instructions
for the relevant power tool). Otherwise the power tool
may have an such unfavourable centre of gravity that you
will not be able to hold onto it securely.
Operate the power tool secured to the mounting plate
u
on the saw stand only. Without the saw stand, the
mounting plate with the power tool will not be stable and
can tip over.
Ensure that long and heavy workpieces do not unbal-
u
ance the saw stand. The free end of long and heavy
workpieces must have something placed underneath it or
be supported.
When pushing together or pulling apart the saw stand,
u
do not put your fingers near the points of articulation.
There is a risk of fingers being crushed.
1 609 92A 6JC | (11.05.2021)
Symbols
The following symbols may provide you with important in-
formation about the use of your saw stand. Please take note
of these symbols and their meaning. Knowing what these
symbols mean will help you to use your saw stand more ef-
fectively and more safely.
Symbols and their meaning
The maximum load bearing capacity
(power tool + workpiece) of the saw
180
stand is kg.
kg
Product description and
specifications
Intended Use
The saw stand is intended for holding the following Bosch
benchtop saws (stand 2021.02):
– GCM 8 S (3 601 L16 0..)
– GCM 8 SJ (3 601 L16 2..)
– GCM 800 S (3 601 L16 1..)
– GCM 10 (0 601 B20 0..)
– GCM 10 J (3 601 M20 2..)
– GCM 10 M (3 601 M20 2..)
– GCM 10 S (0 601 B20 5..)
– GCM 10 SD (0 601 B22 5..)
– GCM 10 X (3 601 M15 0..)
– GCM 10 MX (3 601 M29 0..)
– GCM 12 (0 601 B21 0..)
– GCM 12 GDL (3 601 M23 6..)
– GCM 12 SD (0 601 B23 5..)
– GCM 216 (3 601 M33 0..
– GCM 18V-216 (3 601 M41 0..)
– GCM 18V-305 GDC (3 601 M43 0..)
– GTM 12 (3 601 M15 0..)
The saw stand and power tool are intended for cutting
boards and profiles.

Product Features

The numbering of the components shown refers to the illus-
trations on the graphics pages at the beginning of the
manual.
(1) Holder set
(2) Saw stand
(3) Wheel locking mechanism
(4) Table extension locking knob
(5) Table extension
Handle
(6)
(7) Height-adjustable foot
Bosch Power Tools