Hitachi P 20SD Mode D'emploi page 7

SPECIFICATIONS
Voltage (by areas)*
Power Input
Cutting Width
Max. Cutting Depth
Weight (without cord and guide)
No-Load Speed
*Be sure to check the nameplate on product as it is subject to change by areas.
STANDARD ACCESSORIES
1. Box Wrench (for securing cutter blade) ............... 1
2. Set Gauge (for adjusting cutter height) ............... 1
3. Guide (with set screw) ............................................ 1
4. Depth Guide ............................................................... 1
5. Blade Sharpening Ass'y ........................................... 1
6. Carrying Case ............................................................ 1
Standard accessories are subject to change without no-
tice.
OPTIONAL ACCESSORY (sold separately)
1. Dust Collection Adapter
Optional accessories are subject to change without no-
tice.
APPLICATIONS
Planing various wooden planks and panels.
(See Fig. 1-4)
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized con-
forms to the power requirements specified on the
product nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the
power switch is in the ON position, the power tool
will start operating immediately, which could cause
a serious accident.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
4. Prepare a stable wooden workbench suitable for
planing operation. As a poorly balanced workbench
creates a hazard, ensure it is securely positioned
on firm, level ground.
PLANING PROCEDURES
1. Adjusting the cutter depth:
(1) Turn the knob in the direction indicated by the
arrow in Fig. 5 (clockwise), until the triangular mark
is aligned with the desired cutting depth on the
scale. The scale unit is graduated in millimeters.
(110V, 115V, 120V, 127V, 220V, 230V, 240V)
1100W*
82mm
3mm
4.9kg
16000/min
(2) The cutting depth can be adjusted within a range
of 0-3mm.
2. Surface cutting
Rough cutting should be accomplished at large
cutting depths and at a suitable speed so that
shavings are smoothly ejected from the machine.
To ensure a smoothly finished surface, finish cut-
ting should be accomplished at small cutting depths
and at low speed.
3. Beginning and ending the cutting operation:
As shown in Fig. 6, place the front base of the
planer on the material and support the planer
horizontally. Turn ON the power switch, and slowly
operate the planer toward the leading edge of the
material. Firmly depress the front half of the planer
at the first stage of cutting, as shown in Fig. 7,
depress the rear half of the planer at the end of
the cutting operation. The planer must always be
kept flat throughout the entire cutting operation.
4. Precaution after finishing the planing operation:
When the planer is suspended with one hand after
finishing the planing operation, ensure that the
cutting blades (base) of the planer do not contact
or come too near your body. Failure to do so could
result in serious injury.
BLADE ASSEMBLY AND DISASSEMBLY AND
ADJUSTMENT OF BLADE HEIGHT
1. Blade disassembly:
(1) As shown in Fig. 8, use the accessory box wrench
to loosen the three bolts used to retain the blade,
and remove the blade holder.
(2) As shown in Fig. 9, side the blade in the direction
indicated by the arrow to disassembly the blade.
CAUTION
Be careful not to injure your hands.
2. Blade assembly:
CAUTION
Prior to assembly, thoroughly wipe off all swarf
accumulated on the blade.
(1) Insert a turned portion of the set plate (A) attached
to the blade into a groove on the flat portion of
the cutter block. (Fig. 10, 11)
Set the blade so that both sides of the blade protrude
from the width of the cutter block by about 1 mm
(Fig. 12)
(2) Place the blade holder on the completed assembly,
as shown in Fig. 13, and fasten it with the three
bolts. Ensure that the bolts are securely tightened.
(3) Turn the cutter block over, and set the other side
in the same manner.
English
6