Front Panel; Rear Panel - Numark 4TRAK Guide D'utilisation Rapide

FRONT PANEL

1 2 1
1. FADER START – Enables or disables "fader start" on the corresponding side of the crossfader. When fader
start is enabled on one side, moving the crossfader toward that side will cause the Deck to start playing.
2. CROSSFADER SLOPE – Adjusts the slope of the crossfader curve. Turn the knob to the left for a smooth fade
(mixing) or to the right for a sharp cut (scratching).
3. DECK CROSSFADER ASSIGN – Routes the audio signal of the selected channel as follows:
L = Software and external audio is directed to the left side of the crossfader.
| (center) = Audio is not being controlled by the crossfader but instead routed directly to the program signal.
R = Software and external audio is directed to the right side of the crossfader.
4. HEADPHONE BLEND – Adjust to mix between Cue and Program in the Headphone channel. When turned all
the way left, only channels routed to CUE will be heard. When turned all the way right, only the Program mix
will be heard.
5. SPLIT CUE – When this switch is set to the ON position, the headphone audio will be "split" so that all
channels sent to CUE are mixed to mono and applied to the left headphone channel and the Program mix is
mixed to mono and applied to the right channel. When the switch is in the OFF position, Cue and Program
audio will be "blended" together.
6. HEADPHONE VOLUME – Adjusts the signal volume of the headphone output.
7. HEADPHONE OUTPUT – Connect your 1/4" or 1/8" headphones to this output for cueing and mix monitoring.

REAR PANEL

1 2 3 4
1. POWER SWITCH – Turns 4TRAK on and off. Turn on 4TRAK after all input devices have been connected and
before you turn on amplifiers. Turn off amplifiers before you turn off 4TRAK.
2. POWER INPUT – Use the included power adapter to connect the 4TRAK to a power outlet. While the power is
switched off, plug the power supply into the 4TRAK first, then plug the power supply into a power outlet.
3. USB PORT – Connect the 4TRAK to the included 4TRAK FX KOMMAND CONSOLE and your 4TRAK can be
used as a software controller device using USB MIDI protocol or as a pass-through audio interface.
4. MASTER OUTPUT (XLR) – Connect this XLR output to a PA system or powered monitors.
5. MASTER OUTPUT (RCA) – Use standard RCA cables (not included) to connect this output to a speaker or
amplifier system.
6. BOOTH/ZONE – Use standard RCA cables (not included) to connect this output to a monitoring system.
7. RCA INPUT – Connect audio sources to these inputs.
8. LINE/MIC SWITCH – Flip this switch to the appropriate position, depending on the device connected to the
RCA inputs. If using a line-level device, such as a CD player or sampler, set this switch to "LINE." If using a
microphone, set this switch to "MIC".
9. MIC INPUT – Connect a 1/4" mic to this input.
10. LINE/PHONO SWITCH – Flip this switch to the appropriate position, depending on the device connected to the
RCA inputs. If you are using phono-level turntables, set this switch to "PHONO" to provide the additional
amplification needed for phono-level signals. If using a line-level device, such as a CD player or sampler, set
this switch to "LINE."
11. GROUND – If using phono-level turntables with a grounding wire, connect the grounding wire to these
terminals. If you experience a low "hum" or "buzz", this could mean that your turntables are not grounded.
Note: Some turntables have a grounding wire built into the RCA connection and, therefore, nothing needs to be
connected to the grounding terminal.
3 3
5
4 6
8
7 9 7
10
4
4 5 6
8
7 7
10
7
9
11