Normal Operation; One-Touch Memory - ENZER ET8417 Instructions D'utilisation

Normal Operation

To make a call
To make a call, simply pick up the handset and wait for the dialling tone. Then, dial the desired
telephone number with the numeric keys.
To end a call, replace the handset onto the cradle of the base unit, or push the hook switch.
Operation with On-Hook Dialling and Predialling
This designer's phone is with On-Hook Dialling (OHD) and predialling function.
1. On-Hook Dialling:-
Push the (SPEAKER) button to put your phone off-hook, enter the phone number to be
called, afterwards, the number will be dialled out accordingly. And, OHD works with phone
numbers stored in phone book, one-touch memory, two-touch memory and redial list.
2. Predialling:-
Enter the phone number to be called, then push the
will be dialled out accordingly.
When the dialled number is answered, simply speak or pick up the handset to talk to the other end.
Operation with Headset (Optional)
This designer's phone is equipped with a headset jack. With a headset (purchased separately),
conversation can be made via headset.
1. Connect the headset to the headset connector jack.
2. Follow the On-Hook Dialling procedures to make and answer calls by pushing the
button, and the conversation will be made via headset's mouth and ear pieces.
3. You can switch to handset operation by lifting off the handset.
Operation of Call Back Function
This designer's phone is with call back function which allows you to automatically dial the number
of the person you have called previously. And, it can store maximum up to 10 dialled numbers
in the phone.
1. To make a call from redial memory:-
– In the state of on-hook, press
– Press and buttons to select the number you want to dial.
– Lift the handset or press the
– To delete a single record, simply press
all records, press and hold
" ". Press (DELETE) button again to confirm.
2. To make a call from Caller ID memory:-
– Lift the handset or press (SPEAKER) button and wait for a dialling tone.
– Select the number you want to dial by pressing
– Press (CALL BACK) button to automatically dial the phone number of the caller
shown on the display.
Note: 1. The call back feature will not dial the phone number if the selected call record phone
number is blocked or not available.
2. If the line is busy, pick up the phone to get a dialling tone and then press
BACK) button again. You may also press
dialled.
9
(SPEAKER) button; then the number
(SPEAKER)
(CALL BACK) button once.
(SPEAKER) button, the phone number will be dialled.
(DELETE) button twice. If you want to delete
(DELETE) button until the display shows
and buttons.
(REDIAL/P) button to call the last number
Operation of VIP Function
This designer's phone is with a VIP function. After the VIP number has been set, there will be a
"Beep-Beep" tone when the VIP number calls in.
1. To set a number from the Caller ID memory as VIP:-
– Press
– Press and hold
of the display, and a confirmation "beep" tone should be heard to indicate the number has
been stored to VIP.
– To cancel the VIP setting, simply press and hold
disappears on the display.
2. To store a number from the Phone Book as VIP:-
– Press
number you want to store as a VIP call.
– Press and hold
button until the display shows "VIP". A confirmation "beep" tone should be heard to
indicate the selected number has been stored to VIP.
– To cancel the VIP setting, simply press and hold
buttons at the same time until the "VIP" disappears on the display.

One-Touch Memory

One-Touch Memory provides you with the easiest way to make a call to a frequently used number.
Follow the instructions listed below to store a number (18 digits maximum) into the One-Touch
Memory bank:-
1. You can simply enter the number you want to store first followed by press and hold the One-
Touch Memory ( M1 ..... M3 ) button until the display shows "
2. You can edit a number by using
the One-Touch Memory ( M1 ..... M3 ) button until the display shows "
3. No erasure of direct memory is available in this unit. User can "overwrite" an existing old record.
Or user can save a "blank" record as following steps.
– Press
– Then, the display will show "
– Press the One-Touch Memory (M1, M2......) button until the display shows "
To make a call from the One-Touch Memory:-
To make a call with One-Touch Memory, simply pick up the handset and wait for dialling tone, press
the desired One-Touch Memory ( M1 ..... M3 ) button. And, the stored phone number sequence
will be dialled.
Or, press the One-Touch Memory ( M1 ..... M3 ) button and then lift the handset or press
(SPEAKER) button.
To copy the numbers to the One-Touch Memory :-
Numbers in the Caller ID memory or redial memory can all be copied to the M1~ M3 memory
locations. Do as follows:
– When the number shown on the display, press and hold M1, M2 or M3 until the display
shows "
(CALL
and buttons to select the number you want to store as a VIP call.
(CALL BACK) button until "VIP" appears on the upper left corner
(CALL BACK) button until the "VIP"
(PHONE BOOK) button once followed by
(DELETE) button, then press together with
(DELETE) and
(DELETE) button to erase the wrong entries and then press
(STORE) button once.
".
". The number has now been stored.
GB
and buttons to select the
(CALL BACK)
(CALL BACK)
".
".
".
10