Power Supply; Making The Adjustments; Settings In The On-Screen Menu - Monacor AV-3010RDX Mode D'emploi

4.2.6 Power supply

For power supply a regulated power supply unit is re-
quired with an output voltage between 7 and 30 V
and an output current of 500 mA as a minimum, e. g.
PS-1000ST from MONACOR.
1) In case of power supply units with a variable out-
put voltage, adjust the voltage to 12 V.
2) Connect the power supply unit via a low voltage
plug 5.5/2.5 mm (outside/inside diameter) to the
jack "DC 7 – 30 V" (15). Observe the correct po-
larity in any case: apply the positive pole at the
inner contact of the plug.
3) Do not connect the power supply unit to a mains
socket (230 V~/50 Hz) before all other connec-
tions have been made.

4.3 Making the adjustments

The wireless transmission is made in the 2.4 GHz
range on five channels with a distance of 14 MHz. As
a maximum, three channels can be used simulta-
neously (channels 1, 3, and 5) as two adjacent chan-
nels will interfere with each other. If two channels are
required, several combinations are possible:
channel 1 with channel 3, 4, or 5
channel 2 with channel 4 or 5
channel 3 with channel 5
The AV-3010RDX has 48 programmes on which the
channel numbers and further functions can be stored
via an on-screen menu (see chapter 4.3.1). The re-
ceiver is programmed ex factory as follows:
Programme
1
2
3
4
5
6
7
8
9
10
...
48
The other functions are pre-programmed for all pro-
grammes as follows:
on the menu page 1
Name no name entered
AFC off automatic fine tuning off
Video normal video signal not inverted
Antenna passive 1 antenna jack 1 for DX antenna
w/o preamplifier
AV-Rel. n.c. when receiving a video signal, the
contacts are closed
SW-Rel. n.c. with activated control channel the
contacts are closed
Channel Frequency (MHz)
1 2414.5
2 2428.5
3 2442.5
4 2456.5
5 2470.5
1 2414.5
1 2414.5
1 2414.5
1 2414.5
1 2414.5
... 2414.5
1 2414.5
on menu page 2
Audio on audio reproduction activated
Signal off no signal sound activated
Auto off with switching mode activated the
programme is skipped
Hold off with switching mode activated the
dwell time adjusted in the line
"Auto" is kept
If this factory setting is sufficient, the on-screen menu
need not be called but only the corresponding
programme has to be selected with the button "P+" or
"P-" (6) [see chapter 5].

4.3.1 Settings in the on-screen menu

Switch on the receiver with the switch "power" (1).
Select the programme to be adjusted with the button
"P+" or "P-" (6). Keep the button "OK" (7) pressed for
approx. 3 seconds until the first menu page appears
on the screen. If the receiving signal is too poor or
missing, the menu is highlighted in blue colour for bet-
ter viewing.
Program
Name
Freq.
Channel
AFC
Video
Antenna
AV-Rel.
SW-Rel.
Level
Fig. 4 first menu page
Program
Audio
Signal
Auto
Hold
Day
Month
Year
Hour
Minute
Level
Fig. 5 second menu page
1) To change functions, select the corresponding
menu line with the button "P+" or "P-" (6) and
adjust it with the button "L-" or "L+" (5).
– first menu page –
Program = selected programme number 1– 48
Name = four characters as a maximum to identify
the programme or the camera. All capital letters and
numerals as well as some special characters are
available. The blank space is between "?" and "A".
After selecting the line "Name", the first character
position blinks. Select the desired character with
the button "L+" or "L-". Then go to the next charac-
ter position with the button "P-". From the 4th char-
1
....
2414,5O MHz
1
off
normal
passive 1
n.c.
n.c.
-6-7-8
1
on
off
off
off
06
05
2004
10
34
-6-7-8
13