Bosch 0601868109 Notice Originale page 14

14 | English
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Charging the Battery (see figure A)
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
To remove the battery (5), press the release buttons (4) and
pull the battery downwards out of the power tool. Do not
use force to do this.
Follow the instructions on correct disposal.
Changing the Tool (see figure B)
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
The drill spindle is locked when the on/off switch (7) is not
pressed. This makes it possible to change the application
tool in the drill chuck quickly, conveniently and easily.
1 609 92A 814 | (22.07.2022)
Open the keyless chuck (1) by turning it in the direction of
rotation ➊ until the tool can be inserted. Insert the tool.
Firmly tighten the sleeve of the keyless chuck (1) by turning
it by hand in the direction of rotation ➋ until it audibly clicks
into place. This will automatically lock the drill chuck.
Dust/Chip Extraction
Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one's
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dust, such as oak or beech dust, is considered carci-
nogenic, especially in connection with wood-treatment ad-
ditives (chromate, wood preservative). Materials containing
asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the ma-
terials to be worked.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
Operation
Starting Operation
Inserting the battery
Note: The use of batteries unsuitable for your power tool can
lead to malfunctions or damage to the power tool.
Set the rotational direction switch (6) to the middle position
to avoid unintentionally switching it on. Insert the charged
battery (5) into the handle until you feel it engage and it is
flush with the handle.
Setting the rotational direction (see figure C)
Only operate the rotational direction switch (6) when
u
the power tool is not in use.
The rotational direction switch (6) is used to change the ro-
tational direction of the power tool. However, this is not pos-
sible while the on/off switch (7) is being pressed.
Right rotation: To drill and to drive in screws, press the ro-
tational direction switch (6) through to the left stop.
Left Rotation: To loosen and unscrew screws and nuts,
press the rotational direction switch (6) through to the right
stop.
Preselecting the Torque
The torque presetting ring (2) can be used to preselect the
required torque in 20 stages. When the correct setting is
used, the application tool will be stopped when the screw is
driven flush into the material or once the set torque has been
reached. In position the overload clutch is deactivated,
e.g. for drilling.
When unscrewing screws, you can select a higher setting or
set the tool to the symbol.
Bosch Power Tools