Bosch PRP6A6D70D Notice D'installation page 13

Gas connection elbow: G 1/2
Gas connection R 1/2
→ Fig.
9
Gas connection G 1/2
Replace the gas connection elbow on the appli-
1.
ance with the gas connection elbow G 1/2 sup-
plied in the accessory bag.
→ Fig.
10
Insert the seal between the gas connection of the
2.
appliance and the gas supply.
→ Fig.
11
Electrical connection
¡ This appliance is type Y: The connection cable
must only be replaced by technical customer ser-
vice and not by the user. The cable type and the
minimum cross section must be respected.
¡ The hobs are supplied with a power cord with or
without a plug.
¡ Only connect appliances that are fitted with a plug
to a correctly installed socket with protective earth
conductor.
¡ If the plug is not accessible to the user, an all-pole
isolating safety switch with a minimum contact
opening of 3 mm must be provided.
→ Fig.
12
Converting the gas type
If the country's regulations allow, this appliance can
be adapted to other types of gas, if these are listed
on the rating plate.
You can find the right parts in the bag that is sup-
plied with the appliance or you can obtain them from
customer service. The table → Fig.
right combination for the relevant burner and gas
type.
Economy burner
Standard-output burner
High-output burner
Dual-wok multi-crown burner
¡ 1 - Outer flame
¡ 2 - Inner flame
Tools
Contact technical customer service to purchase the
relevant tools.
Removal lever
Removing the upper part of the appliance (glass
plate with cut-out profiles)
Remove the pan supports, burner caps, distribut-
1.
ors and rotary knobs.
Undo the screws on the burners.
2.
→ Fig.
13
Move the removal lever under the metal cut-out
3.
profile into the area marked for the hob model
and loosen the front clip fastener.
→ Fig.
14
Only use the lever under the cut-out profiles or the
metal frame of the hob.
Carefully lift the glass plate with the cut-out pro-
4.
files to release the rear clip fastener.
Removing the circuit board
10006024
Tip: The circuit board is secured to the holder by
fastening pins at the sides and in the middle. Push
the fastening pins carefully without damaging them.
If one of the pins breaks, the entire holder must be
replaced.
ATTENTION!
The circuit board can be damaged by improper
handling.
▶
▶
▶
1.
2.
3.
→ Fig.
Adjusting the taps
Requirement: The upper part of the appliance and
the circuit board are removed. → "Removing the up-
per part of the appliance (glass plate with cut-out
profiles)", Page 13 → "Removing the circuit board",
Page 13
1.
2.
shows the
29
Replacing the nozzles
▶
Replacing the outer flame nozzle on the multi-crown
burner
Requirement: The upper part of the appliance has
been removed. → "Removing the upper part of the
appliance (glass plate with cut-out profiles)",
Page 13
1.
483196
2.
3.
4.
Replacing the inner flame nozzle on the multi-crown
burner
Requirement: The upper part of the appliance has
been removed. → "Removing the upper part of the
appliance (glass plate with cut-out profiles)",
Page 13
Handle the circuit board carefully.
Use anti-static shields or hold the circuit board at
the edges.
Never touch the surfaces of the circuit board on
which there are components or conducting tracks.
Undo the fastening pins on one side.
Release the fastening pins in the middle by press-
ing on them from both sides with your fingers.
Undo the fastening pins on the other side and re-
move the circuit board.
15
Remove the cylindrical parts and springs from the
fittings spindle.
When adjusting the bypass screws (M), refer to
the table → Fig. .
29
A: Firmly tighten the bypass screws.
‒
B: The bypass screws must be flush with the fit-
‒
ting.
→ Fig.
16
Replace the nozzles using the appropriate wrench
and tighten them carefully to guarantee the seal.
→ Fig.
17
Ensure that the nozzle does not become detached
during removal or fastening.
To gain access to the main nozzle, loosen the
fastening screw and pull the sleeve
→ Fig.
18
Remove the nozzle by turning it anti-clockwise
and screw in the new outer flame nozzle
→ Fig.
19
Set the spacing of the adjustment sleeve for the
air supply to dimension Z, as shown in the table
→ Fig. .
29
→ Fig.
20
Tighten the fastening screw.
→ Fig.
21
back.
⁠
⁠ .
13