Publicité
Les langues disponibles
Les langues disponibles
N100C/N100CPP/N130C TOOL SPECIFICATIONS
All screws and nuts are metric.
TOOL
MODEL
OPERATION
N100C-1
Contact Trip
N100C-2
Sequential Trip
N100CPP-1
Contact Trip
N100CPP-2
Sequential Trip
N130C-2
Sequential Trip
TOOL AIR FITTING:
This tool uses a 3/8 N.P.T. male plug. The inside diameter should be .275" (7mm) or larger. The fitting must be
capable of discharging tool air pressure when disconnected from the air supply. The connector socket on the air
hose should be .275" (7mm) inside diameter or larger.
OPERATING PRESSURE:
70 to 100 p.s.i.g. (4.9 to 7.0 kg/cm
DO NOT EXCEED THIS RECOMMENDED OPERATING PRESSURE.
AIR CONSUMPTION:
The N100C/N100CPP requires 12.6 cubic feet per minute of free air to operate at the rate of 100 nails per minute,
at 80 p.s.i.g. (5.6 kg/cm
nails per minute, at 80 p.s.i.g. (5.6 kg/cm
amount of air required. For instance, if your fastener usage averages 30 nails per minute, you need 50% of the
12.6 c.f.m. which is required for running at 100 nails per minute.
OPERATION
BOSTITCH OFFERS TWO TYPES OF OPERATION FOR THIS SERIES TOOL.
CONTACT TRIP:
The common operating procedure on "Contact Trip" tools is for the operator to contact the work to actuate
the trip mechanism while keeping the trigger pulled, thus driving a fastener each time the work is contacted.
This will allow rapid fastener placement on many jobs, such as sheathing, decking and pallet assembly. All
pneumatic tools are subject to recoil when driving fasteners. The tool may bounce, releasing the trip, and if
unintentionally allowed to recontact the work surface with the trigger still actuated (finger still holding trigger
pulled) an unwanted second fastener will be driven.
SEQUENTIAL TRIP:
The Sequential Trip requires the operator to hold the tool against the work before pulling the trigger. This
makes accurate fastener placement easier, for instance on framing, toe nailing and crating applications.The
Sequential Trip allows exact fastener location without the possibility of driving a second fastener on recoil, as
described under "Contact Trip". The Sequential Trip Tool has a positive safety advantage because it will not
accidentally drive a fastener if the tool is contacted against the work – or anything else – while the operator
MODEL IDENTIFICATION:
Refer to Operation Instructions on page 7 before proceeding to use this tool.
CONTACT TRIP
Identified by:
BLACK TRIGGER
LENGTH
15-3/16" (386mm)
15-3/16" (386mm)
15.19" (386mm)
15.19" (386mm)
15.19" (386mm)
2
). Select the operating pressure within this range for best fastener performance.
2
). The N130C requires 13.5 cubic feet per minute of free air to operate at the rate of 100
2
). Take the actual rate at which the tool will be run to determine the
SEQUENTIAL TRIP
Identified by:
GRAY TRIGGER
HEIGHT
WIDTH
15-1/4" (387mm)
5-9/16" (140mm)
15-1/4" (387mm)
5-9/16" (140mm)
17.75" (451mm)
5.56" (140mm)
17.75" (451mm)
5.56" (140mm)
17.75" (451mm)
5.56" (140mm)
-4-
WEIGHT
10lb. 11oz. (4.8kg)
10lb. 11oz. (4.8kg)
11lbs 15oz (5.4kg)
11lbs 15oz (5.4kg)
12lbs 8ozs (5.6kg)
Publicité
