Makita DA332D Manuel D'instructions page 7

Indicator lamps
Lighted
NOTE: Depending on the conditions of use and the
ambient temperature, the indication may differ slightly
from the actual capacity.
Tool / battery protection system
The tool is equipped with a tool/battery protection sys-
tem. This system automatically cuts off the power to
extend tool and battery life. The tool will automatically
stop during operation if the tool or battery is placed
under one of the following conditions:
Overload protection
This protection works when the tool is operated in a
manner that causes it to draw an abnormally high cur-
rent. In this situation, turn the tool off and stop the appli-
cation that caused the tool to become overloaded. Then
turn the tool on to restart.
Overheat protection
This protection works when the tool or battery is over-
heated. In this situation, let the tool and battery cool
before turning the tool on again.
Overdischarge protection
This protection works when the remaining battery
capacity gets low. If you turn the tool on, it starts again
but stops soon.
In this situation, remove the battery from the tool and
charge the battery.
Switch action
CAUTION:
Before installing the battery car-
tridge into the tool, always check to see that the
switch lever actuates properly and returns to the
"OFF" position when released.
CAUTION:
Be sure to hold the tool firmly
before the tool is switched off.
► Fig.3: 1. Switch lever
To start the tool, simply pull the switch lever. Tool speed
is increased by increasing pressure on the switch lever.
Release the switch lever to stop.
Lighting up the front lamp
CAUTION:
Do not look in the light or see the
source of light directly.
Remaining
capacity
Off
75% to 100%
50% to 75%
25% to 50%
0% to 25%
For model DA332D
► Fig.4: 1. Lamp
For model DA333D
► Fig.5: 1. Lamp
Pull the switch lever to light up the lamp. The lamp
keeps on lighting while the switch lever is being pulled.
The light automatically goes out approximately 10 sec-
onds after the switch lever is released.
NOTE: Use a dry cloth to wipe the dirt off the lens
of the lamp. Be careful not to scratch the lens of the
lamp, or it may lower the illumination.
Reversing switch action
CAUTION:
Always check the direction of
rotation before operation.
CAUTION:
Use the reversing switch only after
the tool comes to a complete stop. Changing the
direction of rotation before the tool stops may dam-
age the tool.
CAUTION:
When not operating the tool,
always set the reversing switch lever to the neu-
tral position.
This tool has a reversing switch to change the direction
of rotation. Depress the reversing switch lever from the
A side for clockwise rotation or from the B side for coun-
terclockwise rotation.
When the reversing switch lever is in the neutral posi-
tion, the switch lever cannot be pulled.
► Fig.6: 1. Reversing switch lever
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing drill bit
Optional accessory
For model DA332D
► Fig.7: 1. Chuck key
To install the drill bit, place it in the chuck as far as it will
go. Tighten the chuck by hand. Place the chuck key in
each of the three holes and tighten clockwise. Be sure
to tighten all three chuck holes evenly.
To remove the drill bit, turn the chuck key counterclock-
wise in just one hole, then loosen the chuck by hand.
After use, return the chuck key to the storage cavity on
the tool.
For model DA333D
► Fig.8: 1. Sleeve
Hold the tool firmly and turn the sleeve counterclock-
wise to open the chuck jaws. Place the drill bit in the
chuck as far as it will go. Hold the tool firmly turn the
sleeve clockwise to tighten the chuck.
To remove the drill bit, hold the tool firmly turn the
7 ENGLISH