Raider RDI-JS29 Manuel D'instructions page 10

www.raider.bg
10
General instructions for safe operation.
Read all instructions carefully. Failure to follow the instructions below may result in electric shock, fire and / or serious injury.
Keep these instructions in a safe place.
1. Safety at work.
1.1. Keep your workplace clean and well lit. Crash and inadequate lighting can contribute to the occurrence of an accident
at work.
1.2. Do not operate the drilling saw in environments with an increased risk of explosion, near flammable liquids, gases or
powders. During operation, the spatter saws sparks out, which can ignite dust or vapors.
1.3. Keep children and side faces at a safe distance while working with the punch. If your attention is diverted, you may lose
control of the punch.
2. Electricity safety.
2.1. The plug of the punch must be suitable for the contact used. Under no circumstances will the design of the plug be
changed. When working with torn electrical appliances, do not use plug adapters. Using original plugs and sockets reduces the
risk of electric shock.
2.2. Avoid touching your body to grounded bodies, e.g. pipes, heaters, stoves and refrigerators. When your body is grounded,
the risk of an electric shock is greater. Protect the saw from rain and moisture. The penetration of water in the punch increases
the risk of electric shock
2.3. Do not use the power cord for purposes for which it is not intended, for example. to carry the cable clamp or to remove
the plug from the socket. Protect the cable from heat, greasing, touching sharp edges or moving parts of machines. Damaged or
twisted cables increase the risk of electric shock.
2.4. When working with a sawing machine outdoors, only switch on the machine with Fi (earth leakage protective circuit
breaker) and the leakage current at which the DTZ is triggered must be no more than 30 mA according to "Regulation 3 for the
layout of electrical systems and power lines ". Only use extensions suitable for outdoor work. The use of an extension designed
to work outdoors reduces the risk of electric shock.
2.5. If the saw is to be used in a damp environment, only connect the machine to Fi-equipped installations. Using such a
leakage current circuit breaker reduces the risk of electric shock.
3. Safe operation.
3.1. Stay focused, keep a close eye on your actions and act cautiously and reasonably. Do not use the punch when you are
tired or under the influence of narcotics, alcohol, or drugs. A moment of distraction when working with a piercing saw can result in
extremely severe injuries.
3.2. Work with protective clothing and always with safety glasses.
Wearing a suitable wearing saw and the work done by personal protective equipment, such as a breathing mask, strong tightly
closed shoes with a stable grapple, protective helmet and silencers, reduce the risk of an accident at work.
3.3. Avoid the risk of inadvertently plugging the punch. Before connecting the plug to the power supply, make sure that the
power switch is set to "off". If, when carrying the punch, you hold your finger on the breaker or if you feed the drilling pin when it is
plugged in, there is a risk of an accident.
3.4. Before turning on a punch, make sure you remove all the tools from it. A helper forgotten on a moving unit can cause
injuries.
3.5. Avoid the unnatural positions of the body. Work in a stable position of the body and at any moment maintain balance. This
will allow you to control the punch better and safer if an unexpected situation arises.
3.6. Work with appropriate clothing. Do not work with wide clothing or jewelery. Keep your hair, clothes and gloves at a safe
distance from the rotating units of the punch. Wide clothes, ornaments, long hair can be captured and dragged by rotating or moving
units.
3.7. If it is possible to use an external aspiration system, make sure it is turned on and functioning properly. The use of an
aspiration system reduces the risks due to the dust released.
4. Careful attitude towards the punch.
4.1. Do not overload the punch. Use the saw blades only according to their intended purpose. You will work better and safer
when using the proper punch in the load range specified by the manufacturer.
4.2. Do not use a piercing saw whose breaker is damaged. A piercing saw that can not be shut off and plugged in as intended
by the manufacturer is dangerous and needs to be repaired
4.3. Before changing the punch settings, replacing work tools and accessories as well as when not using the punch for a long
time, disconnect the plug from the power supply. This measure removes the risk of inadvertent punching.
4.4. Keep saw blades in places where they can not be reached by children. Do not allow them to be used by people who are
unfamiliar with the way they work and have not read these instructions. When in the hands of inexperienced users, punching saws