Publicité
Les langues disponibles
Les langues disponibles
Training area in mm
(for home trainer and user)
Meanings of error message codes
In case of malfunctions may adjoining list of error messages help for people to get function back. Basically, electrical repairs only in compliance with the
relevant safety rules which exists. For more information and assistance in case of malfunctions with our service department (contact details see last page.)
Problem
Potential reasons
-------
Safe lock falls down
E01
After powering on, the electronic me-
ter displays E01
Communication failure from the
electronic meter to the driver, The
electronic meter displays E01 in the
operating process Communication
failure from the driver to the electro-
nic meter
E02
Explosion-proof protection or motor
abnormality
E03
No sensory signal
E04
Lifting learning or self-inspection
fails
E05
Over-current protection
E06
Lifting sensor has no signal
No
display
The controller is not powered on or
on the elec-
is damaged
tronic meter
E09
Controller is in tilt position
Note:
Please contact your local dealer if you have checked all the above listed
things but the problem is still there.
Free area in mm
(Training area and security area
(rotating 60cm))
Solutions
1. Place back the safe lock;
2. Replace safe lock switch or magnetic sensor in the electronic meter; if the problem still fails to
be solved, replace the electronic meter;
1. Check whether the connecting joint between the electronic meter and the core wire of the con-
troller is loose; whether wires are damaged; whether the core wires are in correct connecting order.
2. The controller may be defective. Check and replace a good one.
3. The electronic controller's IC may not be plugged to the place. Check and ensure good plugging.
4. The transformer may be damaged. Check and replace a good one.
1. Check whether the power supply voltage is less than 50% of the normal value; please ensure
correct voltage and test again;
2 Check whether motor wires are well connected; re-connect motor wires, or, if the problem still
fails to be solved, replace the motor;
3. Check whether there is peculiar odor generated by the controller; if yes, it means that IGBT has
been broken down to cause short circuit; then, replace the controller.
Check whether the photoelectric sensor directs to the hole on CD; check whether wires of photo-
electric sensor are damaged and whether terminals of the photoelectric sensor and speed termi-
nals on the controller are firmly connected.
1. Check whether motor signal wires are well inserted; re-insert the signal wire joint to ensure that
it is reliable;
2. Check whether lifting motor's AC wires are properly connected; lifting motor shall be correctly
plugged according to marks on its AC controller;
3. Check whether motor wiring is damaged to form open circuit; if yes, replace wires or replace the
lifting motor;
4. Replace the controller;
5. After all of these inspections, press the learning key for learning again.
1. It may be the system's self-protection against excessive current when the load exceeds the rated
value; restart the machine;
2. Some part of the treadmill is jammed so that the motor can not rotate, thus triggering the self-
protection of the system against excessive current under excessive load; adjust the treadmill and
restart it, or add lubricant.
3. Check whether there is over-current sound or burning odor when the motor is running; replace
the motor;
4. Check whether the controller emits the odor of burning; if yes, replace the controller.
1. Check whether lifting signal wires are damaged.
2. Check whether lifting signal terminals and the controller's lifting terminals are firmly connected.
3. Check whether lifting power cords are damaged.
4. Check whether lifting power cord terminals and the controller's lifting terminals are firmly con-
nected.
1. First of all, check whether the over-load protector has tripped off; if yes, press it;
2. Check the power supply switch, over-load protector and the controller's power cord and trans-
former to ensure well connection;
3. Check whether the power cords from the electronic meter to the controller are well collected;
dismantle the pillar to check connecting joints on each section of the wiring from the electronic me-
ter to the controller; ensure that each wire core is well connected; or the reason may be the com-
munication power cord defect (damaged or broke down); in such case, re-connect or replace wires.
4. The transformer is damaged; replace the transformer
1. When treadmill has incline position no start possible
2. Treadmill is not fold out complete on an even floor
3. Tilt switch at PC board has problem
25
Publicité
