Publicité
Les langues disponibles
Les langues disponibles
User manual of Computer
Function of Displays:
Pulse-Display:
Shows actually heart rate data.
Speed-Display:
Shows actually speed in km/h.
Distance-Display:
Shows actually distance in KM.
Time-Display:
Shows actually time of exercising in minutes and seconds.
Calories-Display:
Shows actually calories in kcal.
Program-No. Display and Incline Display:
Shows actually exercise programs P1~P9 or incline level 1-15.
Program-profile Display:
Shows the exercise profile of exercise programs P1~P9.
Function of keys:
Prog-key:
PROGRAM key: On the stop status, press Prog-key to select ex-
ercising speed programs P1-P9-FAT
F-key:
Select key of time-program H-1, distance program H-2 or calories
program H-3.
Start-key:
Press Start-key to start exercise program (motor starts running) .
Stop/Pause -Key:
Press Stop/Pause-key during exercise to interrupt the program
(motor stops running). Within 5 min. you can press Start-Key to
continue this exercise program or press Stop/Pause -key again
to finish this program. Pre-values can set to zero by pressing the
Stop/Pause-key.
"+"-key:
Press speed up key increase settings or motor speed.
"-"-key:
Press speed down key decrease settings or motor speed.
Quick Speed- keys 2, 5, 9 + 15km/h:
Press one of these keys and the speed changes direct into 2, 5,
9, and 15km/h.
Quick incline- keys 2, 5, 9 + 12%:
Press one of these keys and the inclination
changes direct into 2, 5, 9, and 12%.
MANUAL MODE:
How to start manual mode:
Put in the AC plug in wall power 230V~50Hz and put on the po-
wer switch (78). Put safety clip (74) onto the computer and it will
show normal manual mode.Stand your feet on both side rails. Put
the safety key at you exercise cloth and press start-key to start
with exercising. After a 3 sec. count down, the motor begin to run
slowly and you can step on the running belt and follow the speed.
Adjust the speed with "+" and "-" -keys into desired speed. If put
off the safety clip from computer at any time, the motor stop slow-
ly and the display will show „---". After put on the safety key on
computer the normal manually program will show. Press "+" or "-"
-key to adjust value of speed. Press quick speed -key to adjust
speed quickly. All values of the displays will counter up.
Setting Programs Time-Distance-Calories:
Time Program:
On the normal manual mode, press F-key, to enter time program
H-1. The time display will flash and the initial value is 30:00. Press
"+"-key or "-"-key to set value. The range is: 5:00-99:00. If set a
value the display counts up till zero and then stops running motor.
Distance-Program:
On the normal manual mode, press F-key, to enter distance pro-
gram H-2. The distance display will flash and the initial value is
1,00KM. Press "+"-key or "-"-key to set value. The range is: 1,00-
99:00KM. If set a value the display counts up till zero and then
stops running motor.
Calories-Program:
On the normal manual mode, press F-key, to enter calories pro-
gram H-3. The calories display will flash and the initial value is
500kcal. Press "+"-key or "-"-key to set value. The range is: 20-
990kcal. If set a value the display counts up till zero and then stops
running motor.
RANGE OF ALL FUNCTIONS:
INITAL
TIME(MIN:SEC)
0:00
SPEED(KM/H)
0.0
DISTANCE(KM)
0.00
PULSE(BPM)
P
CALORIES(KCAL)
0
Pulse measurement function
Embrace with both hands, the hand pulse sensors on the com-
puter to order a pulse measurement can be performed. Alterna-
tively use a compatible chest belt (un -coded with transmission
frequency from 5.0-5,5kHz). The measured pulse value is flashing
simultaneously with a heart symbol appear in the pulse display.
Caution: The pulse measurement is not suitable for medical pur-
poses.
23
INITIAL
SETTING
DISPLAY
VALUE
RANGE
RANGE
30:00
5:00-99:00
0:00-99:59
N/A
N/A
1.0-18.0
1.00
1.00-99.00
0.00-99.99
N/A
N/A
50-200
500
20-990
0-999
Publicité
