Publicité
Les langues disponibles
Les langues disponibles
Computer Operations
Selection of the data-display mode (bottom of the screen).
Pressing the MODE button changes the functions in the sub-display.
Clock Time - In Elapsed Time, press and hold the Mode button for two seconds to display Clock
Time. Pressing the Mode button again will return the sub-display to Elapsed Time.
Trip Distance 1 and 2 – The computer has two separate trip distances. Trip Distance 2 is reset
independently. It can be used to record distance within a ride or multiple days distances. In Trip
Distance 1, press and hold the Mode button to select Distance 2. You will continue to view this
distance until you select Distance 1 with the same procedure.
Start or Stop of Measurements.
The computer can be programmed to run in either MANUAL MODE or
AUTO TIME MODE. In Manual Mode you must press the START / STOP
button to turn on and off the Timer, which records Distance and Average
Speeds. In Auto Time
the computer turns the Timer on and off de-
pending on a signal from the sensor.
When speed is detected by the computer and the Timer is running, the
km/h or mph will flash. Speed will appear on the computer screen and
the Odometer will record, regardless if the Timer is running or not.
• Auto Time Mode (Automatic Measurement)
In AUTO TIME mode, the letters
will appear on the computer screen.
Elapsed time, Average and Distance are recorded automatically and the
Timer, stops when the speed stops. In this mode the START/STOP button
is not operable.
• Manual Measurements
When you don't see the icon
on the screen, you can start or stop the
measurements by pushing the START/STOP button.
When you push the button, measurements of Elapsed Time, Average
Speed, Trip Distance 1 and 2 are started and they are stopped with the
second push of the button.
• How to set ON or OFF the auto-mode
Push the SET button on the back side of the computer while Elapsed
Time, Average Speed, Trip Distance 1 or 2 is displayed, then the icon
is lit" (ON) or turned OFF.
Resetting Elapsed Time, Trip Distance, Average Speed and Max Speed.
Press and hold the MODE and START/STOP buttons for 2 sec. in either
the Elapsed Time, Trip Distance 1, Average Speed or Maximum Speed
functions to reset these functions. The Odometer and Trip Distance 2 are
not reset. See below for details.
• Resetting Trip Distance 2
Trip Distance 2 is reset independently. When Trip Distance 2 is on the
screen, press and hold both the MODE and START/STOP buttons to re-
set.
Computer Functions
• Power-saving Function
When no signal has been received for about one hour, the computer goes into the power savings
mode to only display the Clock. When any button is pushed or the wheel is rotated, the computer
screen reappears.
• Dual Tire Size
You can program two,
and
, tire circumferences and can easily switch
versa to enable the system to be used by two bicycles which have different tire sizes. The com-
puter program for circumference
is programmed for low speed use. We recommend to use
this for MTB's.
• Moving Elapsed Time, Average Speed and Maximum
Speed to the upper display.
You can move the Elapsed Time, Average and Max Speed
displays to the upper display for easier viewing. Hold the
START/STOP button for 2 sec. and the sub-display will ap-
pear in the upper display. Hold the START/STOP button
again for 2 sec. and the display returns to the normal set up.
Troubleshooting
No display appears.
Is the battery dead?
Replace it by the new one and do all clear procedure.
Strange data appears
Do all clear procedure (write down the number of Odometer if possible before doing the all
clear procedure and input it manually after choosing the measurement unit).
Measurements do not start when the START/STOP button is pushed.
Is the icon
ON?
Turn the Auto-Mode off to enable the start or stop of the measurements by manual opera-
tion of the button.
No speed data is displayed.
(If the speed data is not displayed, have the contact points short-circuited by a metal plate. In the
case that this short-circuiting is detected by the computer, the computer is considered normal
and the bracket and sensor may possibly have the cause of trouble.)
Is the gap between the sensor and the magnet too big? (should be within 5 mm)
Does the marked line of the sensor align with the center of the magnet?
Adjust the position of the magnet and the sensor.
Make sure that the contact points of the bracket or of the main body are free from dirt.
Wipe the contact points clean.
Is the cord not broken? Even if the outside of the cord looks normal, a breakage in the wire can occur.
Replace the bracket and sensor set with a new one.
Maintenance
• To clean the computer or the attached parts, use diluted neutral detergent
on a soft cloth, and wipe it off with a dry cloth.
Replacing The Battery
When the display gets dim, replace the battery. If you want to retain and
use the current reading of odometer, write down the odometer data before
replacing the battery.
• Put a lithium battery CR2032 in the computer with the (+) mark facing up.
• After replacing the battery, do the necessary set-up of the computer in
accordance with "Computer Set-up".
All manuals and user guides at all-guides.com
Measurement Display
Wheel Icon
Indicates which wheel setting is selected.
Measurement
Unit Icon
Mode Selection Illustrations
(bottom of the screen)
ST/STOP
MODE
Tm
SET
Av
Dst
MODE
ST/STOP
For 2 sec. at the
same time
For 2 sec.
to
or vise
Elapsed
Average
Maximum
Specifications
Time
Speed
Speed
Battery Life : --------------------------------- A Lithium Battery (CR2032), Approx:3 yrs
Upper
Minute
Mx
Av
Second
Part
Lower
Hour
SPD
SPD
Control System : ---------------------------- 4-bit 1-chip micro-computer (with a crystal oscillator)
Part
Display : -------------------------------------- Liquid crystal display
Sensing System : --------------------------- No-contact magnetic sensor
Range of Tire Circumference : ------------- 100 cm – 300 cm (Initial value – A:210 cm B:205 cm)
ST/STOP
Range of Operational Temperature : ------ 0°C
Dimension and Weight(Computer) : ------ 38 x 54 x 17.5 mm [1-1/2 x 2-1/8 x 11/16"] / 28 g [1.0 oz]
* The factory-loaded battery life might be shorter than the above-mentioned specification.
* The specifications and design are subject to change without notice.
Limited Warranty
2-Year Warranty : Computer Head Only
If any trouble or damage occurs during normal use, the product computer will be repaired or replaced
free of charge. Type your name, address, telephone number or e-mail address, date of purchase and
the situation of trouble and send it back together with the product to the closest address below. Trans-
portation charges shall be borne by the customer. After being repaired, the product will be shipped
back to the customer.
* Accessory parts are available for the customers as shown below.
Close
Open
Speed
0.0 (4.0) - 105.9 km/h
[0.0 (3.0) - 65.9 mph]
Average Pace Arrow
It shows that the current speed is faster
or slower than the Average Speed.
Faster
Slower
Auto-mode Icon
When it is lit, the measurements
are automatically started or stopped.
Av
Average Speed
0.0 -105.9 km/h
[0.0 - 65.9 mph]
Dst
Trip distance - 1
0.00 -999.99 km [mile]
Trip distance - 2
0.00 - 999.99 km
[mile]
MODE
* Resetting of Dst2 only
Odo
Odometer
0.0 - 99999 km [mile]
Mx
Maximum Speed
0.0 (4.0) - 105.0 km/h
[0.0(3.0) - 65.0 mph]
Tm
Elapsed Time
0:00'00" - 9:59'59"
Return to Clock display
MODE
MODE
Clock
SET
0:00 - 23:59
[1:00 - 12:59]
When the measurements
are stopped.
(approx:1 hrs per day usage)
40°C [32°F
–
(excluding the attached parts and deteriorated battery )
CO.,LTD.
2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan
Attn.: CAT EYE Customer Service Section
Service & Research Address for United States Consumers:
CAT EYE Service & Research Center
1705 14th St. 115 Boulder, CO 80302
Phone: 303-443-4595
Fax: 303-473-0006
#169-9300 [169-9305]
Bracket Sensor Kit [Long]
#169-9755
Attachment Kit
#169-9350
Heavy Duty Wire and Bracket
Sensor Kit
#169-9303
Bracket Sensor Kit for Aero Bar
#169-9304
Stem Mount Bracket Kit
Power Saving Screen
(When no signal is received for about one hour,
the computer switches to the power-saving mode)
When you push either of the
MODE button or the
START/STOP button or you
ride the bicycle, the display
comes back to the
measurement display.
You can program
two tire sizes and
use either of them.
Road
MTB
How to select tire size
or
When data other than Odo is
displayed
SET
Keep on pressing the
button for two seconds
When the Odo data is
displayed
MODE
ST/STOP
Road
MTB
Keep on pressing buttons
for 2 sec. at the same time
Inputting the Tire
Circumference
Range of setting:
100 - 300 cm
Return to Odo
SET
SET
When the measurements
are stopped
Increase
Decrease
the number
the number
MODE
ST/STOP
Setting The Clock Time
24 hour or 12 hour system is to
be used with km/h or mph unit respectively
Increase the number
MODE
SET
ST/STOP
Set the hour
Set the minute
104°F]
–
Toll Free: 800-5CATEYE
e-mail: service@cateye.com
URL: http://www.cateye.com
#169-9691
Wheel Magnet
#166-5150
Lithium Battery (CR2032)
#169-9302
[#169-9307]
Center Mount Bracket
Kit [Long]
#169-9760
Magnet for
Composite Wheel
Publicité
