Bavaria BBC 52 Mode D'emploi D'origine page 19

Danger!
Sound and vibration
L sound pressure level ..................... 92.1 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ..................... 112.1 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Operation
Vibration emission value a
Uncertainty K = 1.5 m/s
Handle on the right
Vibration emission value a
Uncertainty K = 1.5 m/s
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
5. Assembly
5.1.1 Fitting the long handle (Fig. 3)
Using the 4 Allen screws M6x30 (28), fasten the
long handle assembly (14) to the engine assem-
bly (13).
5.1.2 Fitting the steady grip
Fit the left steady grip (2b) or the right steady grip
(2a) as shown in Figs. 4-4a. The holes in the stea-
dy grips are for receiving the screws. Tighten the
screws (29) securely at the top part of the steady
grip holder (25).
5.1.3 Fastening the harness and cable
Hook the harness (15) into the holder as shown
in Fig. 5. Then use the supplied cable ties (18) to
fasten the cable to the long handle and the steady
grip.
Anl_BBC_52_SPK7.indb 19 Anl_BBC_52_SPK7.indb 19
GB
= 13.846 m/s
2
h
2
= 10.602 m/s
2
h
2
- 19 -
5.1.4 Fitting the cutting blade guard hood
Important: The cutting blade guard hood must
be fi tted if you want to work with the cutting blade.
Using the two screws M6x16 (30), secure the cut-
ting blade guard hood (26) to the clip provided as
shown in Fig. 6.
5.1.5 Fitting/Replacing the cutting blade
The procedure for fi tting the cutting blade is
shown in Figs. 7a-7f. To dismantle, proceed in
reverse order.
•
Plug the carrier plate (32) onto the spline
shaft (Fig. 7b)
•
Lock the cutting blade (27) on the carrier pla-
te (Fig. 7c)
•
Plug the pressure plate (33) over the thread
of the spline shaft (Fig. 7d).
•
Plug on the cover of the pressure plate (34)
(Fig. 7e).
•
Look for the hole in the carrier plate, line up
with the notch underneath and lock with the
supplied Allen key (22) in order to now tighten
the nut (35) (Fig. 7f). Important: Left-hand
thread
5.1.6 Fitting the line cutter
Using the three screws (31), secure the line cutter
(17) to the cutting line guard (24) as shown in Fig.
8. Risk of injury – wear safety gloves.
5.1.7 Fitting the cutting line guard to the
cutting blade guard hood
Important: The cutting line guard hood must be
fi tted in addition if you want to work with the cut-
ting line.
The cutting line guard (24) is pressed into the
mounts on the blade guard hood (26) as shown in
Fig. 9. Important: The cutting line cutter is on the
cutting line guard – risk of injury!
5.1.8 Fitting/Replacing the line spool
The procedure for fi tting the line spool is shown in
Fig. 10. To dismantle, proceed in reverse order.
Look for the hole in the carrier plate, line up with
the notch underneath and lock with the supplied
Allen key (22) in order to now screw the line spool
(16) onto the thread. Important: Left-hand thread
13.01.16 08:31 13.01.16 08:31