Télécharger Imprimer la page

KitchenAid KDTE104ESS1 Mode D'emploi page 12

Publicité

Les langues disponibles

Les langues disponibles

CONTROLS AND CYCLE STATUS
CONTROL
PURPOSE
To reset any cycle
and options during
selection or to cancel
a wash cycle and
drain the dishwasher
after it has started.
To turn the audible
tones on or off.
CONTROLS AND CYCLE STATUS
CONTROL
Canceling a Cycle
1. Open the door slightly to stop the cycle. Wait for the spraying
action to stop before completely opening the door.
2. Press and hold CANCEL/DRAIN button once. The Cancel/
Drain light will light up.
3. Close the door and the dishwasher starts a drain cycle (if water
remains in bottom of dishwasher). Let the dishwasher drain
completely. The Cancel/Drain light turns off after 2 minutes.
Changing a Cycle After Dishwasher Is Started
1. You can interrupt a cycle and restart your dishwasher from the
beginning using the following procedure.
2. Open the door slightly to stop the cycle. Wait for the spraying
action to stop, then open the door completely.
3. Check that detergent dispenser cover is still closed. If cover is
open, you will need to refill the detergent dispenser before
restarting your new cycle.
4. Press CANCEL/DRAIN and wait approximately 2 minutes until
the machine drains and the Cancel/Drain light turns off.
5. Select new cycles and options.
6. Press START/RESUME.
12
COMMENTS
Press and hold CANCEL/DRAIN to reset any control selections made.
See the "Canceling A Cycle After Dishwasher Is Started" and "Changing A Cycle After
Dishwasher Is Started" sections.
Press and hold the HI TEMP WASH button for 3 seconds to turn the audible tones on or
off. Only audible tones for confirming button presses can be turned on/off. Important
audible tones, such as indicating a cycle has been interrupted, cannot be deactivated.
Dishwasher Feedback Section
PURPOSE
The Cycle Status
A
Indicator Light is
used to follow the
progress of the
dishwasher cycle. It
is located on the
front of the door.
The Cycle Status
Display is used to
follow the progress
of the dishwasher
cycle, and to show
other information.
COMMENTS
The single indicator light on the front of the door panel (A) will remain blue
during wash/rinse, red during dry, and white when complete.
The Time Display is used for estimated cycle time and also for delay hours.
Estimated cycle time is displayed in hours and minutes as you make cycle and
option selections. After you start the dishwasher, the display counts down
the time.
After you press the Start/Resume button, the Time Display counts down
seconds to close the door. If the door is not closed by the end of the
countdown you will hear a series of beeps and the cycle will not start.
When you select the Delay feature, the Time Display will give the number of
hours followed by an "H".
Adding a Dish After Dishwasher Is Started
If your dishwasher has an "Add Dish" indicator:
1. Open the door slightly to stop the cycle. Wait for the spraying
action to stop and then completely open the door.
2. Add a dish to the load while the indicator is lit.
3. Press the START/RESUME button and close the door. If the
door is not closed before the countdown timer ends you will
hear a series of beeps and the dishwasher will not start.
If your dishwasher does not have "Add Dish" indicator:
1. Open the door slightly to stop the cycle. Wait for the spraying
action to stop and then completely open the door.
2. If the detergent dispenser door is closed you may add a dish. If
the detergent dispenser door is already opened an added dish
might not be cleaned.
3. Press the START/RESUME button and close the door. If the
door is not closed before the countdown timer ends you will
hear a series of beeps and the dishwasher will not start.

Publicité

loading