Publicité
Liens rapides
All manuals and user guides at all-guides.com
Operation / Fonctionnement / Funcionamiento
Electric Airless Sprayers
Pulvérisateurs électriques type Airless
Pulverizadores eléctricos sin aire
- For Portable Airless Spraying of Architectural Coatings and Paints -
3300 psi (227 bar, 22.7 MPa) Maximum Working Pressure
IMPORTANT SAFETY INSTRUCTIONS.
Read all warnings and instructions in this manual.
Save these instructions.
Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441
Copyright 2006, Graco Inc. is registered to I.S. EN ISO 9001
311360C
Publicité
Manuels Connexes pour Graco 695 HI
Sommaire des Matières pour Graco 695 HI
- Page 1 3300 psi (227 bar, 22.7 MPa) Maximum Working Pressure IMPORTANT SAFETY INSTRUCTIONS. Read all warnings and instructions in this manual. Save these instructions. Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441 Copyright 2006, Graco Inc. is registered to I.S. EN ISO 9001...
- Page 2 All manuals and user guides at all-guides.com Warnings Warnings The following are general warnings related to the setup, use, grounding, maintenance and repair of this equipment. Additional, more specific warnings may be found throughout the body of this manual where applicable. Symbols appearing in the body of the manual refer to these general warnings.
- Page 3 Read fluid and solvent manufacturer’s warnings. For complete information about your material, request MSDS from distributor or retailer. • Check equipment daily. Repair or replace worn or damaged parts immediately with genuine Graco replacement parts only. • Do not alter or modify equipment.
- Page 4 All manuals and user guides at all-guides.com Mise en garde Mise en garde Les mises en garde suivantes sont des mises en garde de sécurité relatives à la configuration, utilisation, mise à la terre, maintenance et réparation de ce matériel. D’autres mises en garde plus spécifiques figurent dans ce manuel aux endroits concernés.
- Page 5 à votre distributeur ou revendeur. • Vérifier l’équipement tous les jours. Réparer ou remplacer immédiatement les pièces usées ou endommagées par des pièces de rechange d’origine Graco. • Ne pas modifier cet équipement.
- Page 6 All manuals and user guides at all-guides.com Advertencias Advertencias A continuación se ofrecen advertencias en general relacionadas con la seguridad de la puesta en marcha, utilización, conexión a tierra, mantenimiento y reparación de este equipo. Además, puede encontrar advertencias adicionales a lo largo de este manual siempre que sea pertinente.
- Page 7 MSDS al distribuidor o al minorista. • Revise el equipo a diario. Repare o cambie inmediatamente las piezas desgastadas o deterioradas únicamente con piezas de repuesto genuinas de Graco. • No altere ni modifique el equipo.
- Page 8 All manuals and user guides at all-guides.com Component Identification / Identification des composants / Identificación de los componentes Component Identification / Identification des composants / Identificación de los componentes English Français Español Premium Digital Display Affichage numérique Pantalla digital Premium Premium ON/OFF switch Bouton MARCHE/ARRÊT...
- Page 9 All manuals and user guides at all-guides.com Grounding / Mise à la terre / Conexión a tierra Grounding / Mise à la terre / Conexión a tierra English Français Español The sprayer must be Ce pulvérisateur doit Este pulverizador grounded. Grounding être raccordé...
- Page 10 All manuals and user guides at all-guides.com Grounding / Mise à la terre / Conexión a tierra Ground 120 volt plug ti4297a ti4295 Power Requirements Extension Cords • Do not modify plug! If it will not fit • 100-120V units require •...
- Page 11 All manuals and user guides at all-guides.com Grounding / Mise à la terre / Conexión a tierra Pails • Solvent and oil/based fluids: • Do not place pail on a nonconduc- • Grounding a metal pail: connect a • To maintain grounding con- follow local code.
- Page 12 All manuals and user guides at all-guides.com Pressure Relief Procedure / Décompression / Descompresión Pressure Relief Procedure / Décompression / Descompresión ti4265a ti2599a WASTE RESÍDUOS À JETER DESECHO FLUSH ti2595a Pressure Relief Turn power OFF. Wait Lock gun trigger safety. Turn pressure to lowest Put drain tube in pail.
- Page 13 All manuals and user guides at all-guides.com Setup / Installation / Puesta en marcha Setup / Installation / Puesta en marcha ti2703a ti2702a ti4252a Connect Graco airless hose Connect other end of hose Tighten securely. Remove tip guard. to sprayer. to gun.
- Page 14 Check inlet strainer for clogs Fill throat packing nut with Turn power OFF. Plug power supply cord and debris. Graco TSL to prevent pre- into a properly grounded mature packing wear. electrical outlet. Do this each time you spray. Vérifier si la crépine d’entrée Remplir l’écrou du...
- Page 15 All manuals and user guides at all-guides.com Setup / Installation / Puesta en marcha PAINT FLUSH ti2756a Turn prime valve down. Place siphon tube set in grounded metal pail partially filled with flushing fluid. Attach a ground wire to pail and to true earth ground. Do 1. - 5. of Startup to flush out storage oil shipped in sprayer. Use water to flush water-base paint and mineral spirits to flush oil-base paint and storage oil.
- Page 16 All manuals and user guides at all-guides.com Startup / Démarrage / Puesta en marcha Startup / Démarrage / Puesta en marcha ti4266a 15sec Turn pressure control to Turn power ON. Increase pressure 1/2 to Turn prime valve up to close lowest pressure.
- Page 17 All manuals and user guides at all-guides.com Startup / Démarrage / Puesta en marcha ti4271a ti2713a ti2714a ti2599a WASTE PAINT FLUSH Hold gun against grounded Inspect for leaks. Do not stop Place siphon tube in paint Trigger gun again into flushing metal flushing pail.
- Page 18 All manuals and user guides at all-guides.com Startup / Démarrage / Puesta en marcha ti2710a ti2708a ti2709a Insert SwitchTip. Insert metal seal and OneSeal. Screw assembly onto gun. Tighten. Monter la buse SwitchTip. Mettre un joint métallique et un joint type Visser l’ensemble sur le pistolet.
- Page 19 All manuals and user guides at all-guides.com Startup / Démarrage / Puesta en marcha heavy edges ti2758a ti2757a ti2760a ti2759a Spray Clear Clog 1 Spray test pattern. Adjust pres- 2 Hold gun perpendicular, 1 Release trigger, put safety ON. 2 Put safety ON. Return SwitchTip sure to eliminate heavy edges.
- Page 20 All manuals and user guides at all-guides.com ™ ™ ™ WatchDog Protection System / Système de protection WatchDog / Sistema de protección WatchDog ™ ™ WatchDog Protection System / Système de protection WatchDog ™ Sistema de protección WatchDog Pump stops automatically when material pail is empty To activate: Premium units with digital display: Turn WatchDog switch OFF.
- Page 21 All manuals and user guides at all-guides.com Digital Tracking System / Système de suivi numérique / Sistema de rastreo digital Digital Tracking System / Système de suivi numérique / Sistema de rastreo digital ti4266a ti2599a FLUSH Operation Main Menu Change Display Units Short press to move to next display.
- Page 22 All manuals and user guides at all-guides.com Digital Tracking System / Système de suivi numérique / Sistema de rastreo digital Operation Main Menu Short press DTS button to move Press and hold to reset to zero, Short press DTS button to move Short press DTS button to to Job Gallons (or liters x 10).
- Page 23 All manuals and user guides at all-guides.com Digital Tracking System / Système de suivi numérique / Sistema de rastreo digital ti4266a ™ Secondary Menu - Stored Data and WatchDog Pump Protection Modes Do Pressure Relief, Turn power switch on while The sprayer model briefly Short press DTS button and steps 1 - 4 if they have not...
- Page 24 All manuals and user guides at all-guides.com Digital Tracking System / Système de suivi numérique / Sistema de rastreo digital ™ Secondary Menu - Stored Data and WatchDog Pump Protection Modes Short press DTS Press and hold DTS Short press DTS button. Press and hold (8 seconds) W-DOG scrolls past then DTS button to move to...
- Page 25 All manuals and user guides at all-guides.com Cleanup / Nettoyage / Limpieza Cleanup / Nettoyage / Limpieza ti4266a ti2599b ti4271a ti2770a PAINT WASTE PAINT FLUSH ti2756a Do Pressure Relief, steps 1 - 4. NOTE: Use water for water base paint Increase pressure to 1/2.
- Page 26 All manuals and user guides at all-guides.com Cleanup / Nettoyage / Limpieza ti2713a PAINT ti2820a FLUSH ti2718a WASTE Turn prime valve down to open Raise siphon tube above flushing Turn prime valve up to close drain Turn prime valve down to drain valve and allow flushing fluid and run sprayer for 15 to valve.
- Page 27 All manuals and user guides at all-guides.com Cleanup / Nettoyage / Limpieza ti2776a Pump Armor ti2814b ti2895a Remove filters from gun and sprayer, if If flushing with water, flush again with Wipe sprayer, hose and gun with a rag installed. Clean and inspect. Install fil- mineral spirits, or Pump Armor, to leave soaked in water or mineral spirits.
- Page 28 All manuals and user guides at all-guides.com Technical Data Technical Data Maximum Tip 220 - Size 100 - 240V Generator Cycles Maximum Fluid 120V, A, XXX, A, Minimum Motor per gallon Delivery Outlet Model HP (W) (liter) gpm (lpm) Guns npsm 14.8, 5000...
- Page 29 All manuals and user guides at all-guides.com Caractéristiques techniques Caractéristiques techniques Taille de buse 220 - maxi 100- 240V Cycles par Débit Sortie 120V, A, XXX, A, Génératrice Moteur gallon maximum 1 pis- 2 pis- produit Modèle Minimum W HP (W) (litre) gpm (lpm) tolet...
- Page 30 All manuals and user guides at all-guides.com Características técnicas Características técnicas Tamaño máximo 220 - Salida de la boquilla 100- 240V A mínima CV del Ciclos por Caudal 120V, A, XXX, A, del gene- motor galón máximo fluido Modelo rador (litro) gpm (lpm) pistola...
- Page 31 All manuals and user guides at all-guides.com Notes / Remarques / Notas Notes / Remarques / Notas 311360C...
- Page 32 With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of 36 months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.