WORLD DRYER ADVANTAGE Serie Manuel Du Propriétaire

Instructions apply to the following models: AD90, AD90-M, AD90-BG, AD90-SS
Installation Instructions
WARNING: Do NOT modify the product in ANY way
Modifications including cutting holes may cause damage to the unit and will VOID the warranty
WARNING: Installation Shall be Performed by a Qualified Licensed Electrician
1. Remove cover by removing (2) tamper-proof screws using security wrench
supplied. Pull cover directly toward you. IMPORTANT: S
2. Dryers should be placed at least 2 feet (61cm) apart and at least 12" (30cm)
from washbasin. Do not install dryer over washbasin. Dryers should be at
least 18" (46cm) above any projection which may interfere with the operation
of the automatic sensor.
Hold the backplate to the wall at the suggested MAXIMUM mounting height.
Measure from bottom edge of the backplate to the floor.
3. Mark the locations of the four mounting holes and the conduit entrance
location on the wall. (The conduit entrance is the proper hole diameter for
1/2 inch (13mm) conduit.)
4. Fasten the backplate to the wall where previously marked.
RECOMMENDATION:
Wood wall – No. 14 (M6) wood screws, 2-3/4" (70mm) long
Cement or brick – 1/4" (M6) stud expansion bolts, 3" (76mm) long
Hollow wall – 1/4" (M6) toggle bolts, length depends on wall thickness
5. Run a single phase 120V or 230V 50/60Hz electrical service wire to the dryer
location using either the in-wall or bottom surface 1/2"conduit entrance and
connect to the lead wires as shown on the dryer schematic. The ground wire
must be connected to the dryer ground screw. IMPORTANT: All units must
be supplied with 3 wire service. Use No. 12 or 14 wire as required by local
electrical rules. Unit must be installed with separate disconnect means by a
qualified licensed electrician.
CONNECT TO A DEDICATED CIRCUIT NOT TO EXCEED 20 AMPS
Dryers located in shower rooms or other wet locations should be equipped
with ground fault interrupter(s).
6. Carefully replace the cover using (2) tamper-proof screws supplied. Apply a
bead of caulk around edges of cover to wall.
P L
arts ist
ITEM PART NO. DESCRIPTION
1 GX202 COVER, WHITE ABS*
2 GX202-M COVER, WHITE STEEL*
3 GX202-BG COVER, BLACK STEEL*
4 GX202-SS COVER, STAINLESS STEEL*
5 GX212-A VENT ASS'Y W/LENS AND FOAM GASKET
6 AD216 MOTOR, 110-120V
7 GX218-1 HEATING ELEMENT 110-120V (ADVANTAGE ONLY)
8 GX228 BLOWER WHEEL
9 SM239 SMART SENSOR COMPLETE 100-240 VOLT
10 SM239-HAIR HAIR DRYER SMART SENSOR 100-240 VOLT
11 GB232 TAMPER-PROOF SCREWS & SECURITY WRENCH
* Must specify complete model number
A ™
dvAntAge
Owner's Manual
S
ave ecurity
Series Hand & Hair Dryer
5-5/8
.
W (143mm)
rench
FROM BOTTOM OF DRYER TO FINISHED FLOOR (STANDARD)
All Hand Dryers
Advantage Hair Dryer
FROM BOTTOM OF DRYER TO FINISHED FLOOR (METRIC)
All Hand Dryers
Advantage Hair Dryer
E V
xploded iew
7
1
2
3
4
AD90_Advantage-Series_illustration-3
WARNING: Disconnect Power Before Servicing
WARNING: For Indoor Use Only.
Mounting Diagram
9
16 " 15mm Max.
9
16 " 15mm Max.
3
8 16 " 208mm
Template is for all
American Dryer
EXTREMEAIR, ADVANTAGE
AND GLOBAL Series dryers
3
9 8 " 238mm Max.
1
10 8 " 258mm Max.
7
8 " 22mm
Conduit Entrance
Outer perimeter
of ABS Cover
Revised 10/06/2014
Series Surface Mount
A
dvAntAge
RECOMMENDED MOUNTING HEIGHTS
Men Women
44" 42"
74" 68"
RECOMMENDED MOUNTING HEIGHTS
Men Women
112cm 107cm
187cm 172cm
8
Wednesday, April 24, 2013 10:44:58 AM
Mounting Holes for
1/4" [M6] screws
15
8 16 " 228mm
15
16 " 24mm
1
1 2 " 38mm
Children Disabled
32"- 42" 36"
48"- 68" 48"
Children Disabled
81-107cm 91cm
121-172cm 121cm
6
9
10
5
11
Jay Harnish