Kenwood DPX793BH Mode D'emploi page 34

AUDIO SETTINGS
SPEAKER SIZE The frequency and slope settings are automatically set for the crossover of
the selected speaker.
FRONT SIZE 3.5"/4"/4.75"/5"/6.5"/6.75"/7"/4×6/5×7/6×8/
6×9/7×10: Selects according to the connected speaker
size for optimum performance.
TWEETER SMALL/MIDDLE/LARGE: Selects according to the
size range of the connected tweeter for optimum
performance. ; NONE: Not connected.
REAR 3.5"/4"/4.75"/5"/6.5"/6.75"/7"/4×6/5×7/6×8/6×9/7×10:
Selects according to the connected speaker size for optimum
performance. ; NONE: Not connected.
SUBWOOFER 6.5"/8"/10"/12"/15" OVER: Selects according to the connected speaker
size for optimum performance. ; NONE: Not connected.
X ' OVER
TWEETER FRQ 1KHZ/1.6KHZ/2.5KHZ/4KHZ/5KHZ/6.3KHZ/8KHZ/
10KHZ/12.5KHZ: Adjusts the crossover frequency for
the tweeter speaker.
GAIN LEFT –8 to 0: Adjusts the output volume of the left tweeter.
GAIN RIGHT –8 to 0: Adjusts the output volume of the right tweeter.
FRONT HPF F - HPF FRQ 30HZ/40HZ/50HZ/60HZ/70HZ/80HZ/90HZ/100HZ/
120HZ/150HZ/180HZ/220HZ/250HZ: Adjusts the
crossover frequency for the selected speakers (high
pass filter). ; THROUGH: All signals are sent to the
selected speakers.
F - HPF SLOPE –6DB/–12DB/–18DB/–24DB: Adjusts the crossover
slope.
(Selectable only if a setting other than [THROUGH] is
selected for [F - HPF FRQ].)
F - HPF GAIN –8 to 0: Adjusts the output volume of the selected
speaker.
30
ENGLISH
REAR HPF R - HPF FRQ
R - HPF SLOPE
R - HPF GAIN
SUBWOOFER SW LPF FRQ
LPF
SW LPF SLOPE
SW LPF PHASE
SW LPF GAIN
DTA SETTINGS
For settings, 31, Digital Time Alignment settings.
CAR SETTINGS
• The following item is selectable only if [SUBWOOFER SET] is set to [ON] ( 29):
– [SUB-W LEVEL]
– [SUBWOOFER] of [SPEAKER SIZE]
– [SUBWOOFER LPF] of [X ' OVER]
– [SUBWOOFER] of [DISTANCE] and [GAIN] in [DTA SETTINGS]
• The following item is selectable only if a setting other than [NONE] is selected for
[TWEETER], [REAR] and [SUBWOOFER] of [SPEAKER SIZE]:
– [TWEETER], [REAR HPF], [SUBWOOFER LPF] of [X ' OVER]
(Refer FRONT HPF settings.)
30HZ/40HZ/50HZ/60HZ/70HZ/80HZ/90HZ/
100HZ/120HZ/150HZ/180HZ/220HZ/250HZ:
Adjusts the crossover frequency for the subwoofer
(low pass filter). ; THROUGH: All signals are sent to
the subwoofer.
–6DB/–12DB/–18DB/–24DB: Adjusts the
crossover slope.
(Selectable only if a setting other than [THROUGH] is
selected for [SW LPF FRQ].)
REVERSE (180°)/NORMAL (0°): Selects the phase
of the subwoofer output to be in line with the
speaker output for optimum performance.
–8 to 0: Adjusts the output volume of the
subwoofer.