Ingersoll Rand CA Serie Mode D'emploi page 18

PART NUMBER FOR ORDERING
Common parts for ALL CA Grinders
1 Inlet Assembly . . . . . . . . . . . . . . . . . . . . . . . . . LG1–A465A
2 Inlet Screen . . . . . . . . . . . . . . . . . . . . . . . . R1602–61
3 Inlet Seal . . . . . . . . . . . . . . . . . . . . . . . . . . 85H–167
Throttle Valve Cartridge Kit . . . . . . . . . . . . . . LG1–K300
4 Throttle Valve Cartridge Case . . . . . . . . . . LG1–300A
4A Throttle Valve Seat . . . . . . . . . . . . . . . . . . LG1–303
4B Throttle Valve . . . . . . . . . . . . . . . . . . . . . . AG210–302
4C Throttle Valve Spring . . . . . . . . . . . . . . . . . 7L–51
4D Throttle Valve Spring Seat . . . . . . . . . . . . . LG1–592
5 Motor Housing . . . . . . . . . . . . . . . . . . . . . . . . . LG1–40
6 Throttle Lever . . . . . . . . . . . . . . . . . . . . . . . . . LG1–273
6A Locking Throttle Lever Assembly
(for models ending in L, C, ML or MC) . . . . . LG1–A400
* Lever Lock . . . . . . . . . . . . . . . . . . . . . . . . . LG1–402
* Lock Spring . . . . . . . . . . . . . . . . . . . . . . . . LG1–405
* Lock Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . 5UT–757
7 Throttle Lever Pin . . . . . . . . . . . . . . . . . . . . . . 61H–120
8 Throttle Valve Plunger . . . . . . . . . . . . . . . . . . . LG1–191
9 Rear Rotor Bearing . . . . . . . . . . . . . . . . . . . . . DG230–22
10 Rear Rotor Bearing Spacer (2) . . . . . . . . . . . . DG20–278
11 Rear Rotor Bearing Retainer . . . . . . . . . . . . . . LG1–118
* Not illustrated.
To keep downtime to a minimum, it is desirable to have on hand certain repair parts. We recommend that you stock one (pair or set) of each part indicated by
a bullet ( ) for every four tools in service.
# Always install a Locking Throttle Lever Assembly (6A) on a tool with a Low Profile Concentric Flange (19A). Do not equip a tool with a
standard non–locking Throttle Lever (6) and Low Profile Concentric Flange. This can allow the tool to continue to run if dropped or set down.
All manuals and user guides at all-guides.com
#
PART NUMBER FOR ORDERING
12 Rotor
for CA120 (5 vane slots) . . . . . . LG1–53–5
for CA200 (3 vane slots) . . . . . . LG1–53–3
13 Vane Packet (set of 5 Vanes) . . . . . . . . . . . LG1–42–5
14 Front End Plate . . . . . . . . . . . . . . . . . . . . . LG1–11
15 Front End Plate Spacer . . . . . . . . . . . . . . . DG10–65–5
16 Front Seal Cup . . . . . . . . . . . . . . . . . . . . . . LG1–32
17 Front Rotor Bearing . . . . . . . . . . . . . . . . . . LG1–24
18 Flow Ring
for CA120 (12 000 rpm)
(brown) . . . . . . . . . . . . . . . . . . . . LG1–103–1
for CA200 (20 000 rpm)
(red) . . . . . . . . . . . . . . . . . . . . . . LG1–103–3
19 High Profile Flange . . . . . . . . . . . . . . . . . . LG1–23
19A Low Profile Concentric Flange
(for all models ending in C) . . . . . . . . . . . LG1R–23
20 Flange Clamp . . . . . . . . . . . . . . . . . . . . . . . LG1–29
21 Bevel Pinion and Bevel Gear
(sold only as a matched set)
for CA120 . . . . . . . . . . . . . . . . . LA1–A552–2.0S
for CA200 . . . . . . . . . . . . . . . . . LA1–A552–1.5A