Publicité
Les langues disponibles
Les langues disponibles
TECHNICAL DATA
Production code.......................................................................................................................
............................................................................................................................................
............................................................................................................................................
............................................................................................................................................
Rated input ..............................................................................................................................
Output ......................................................................................................................................
No-load speed .........................................................................................................................
Speed under load max. ...........................................................................................................
Rate of percussion under load max. ........................................................................................
Impact energy per stroke according to EPTA-Procedure 05/2009 .........................................
Drilling capacity in concrete .....................................................................................................
Tunnel bit in concrete, bricks and limestone ...........................................................................
Core cutter in concrete, bricks and limestone .........................................................................
Chuck neck diameter ...............................................................................................................
Weight according EPTA-Procedure 01/2014 ...........................................................................
Noise Information K545 S
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) ....................................................................
Sound power level (Uncertainty K=3dB(A)) ........................................................................
Wear ear protectors!
Noise Information K500 S
Typically the A-weighted sound pressure level of the
tool is .......................................................................................................................................
Measured values determined according to 2005/88/EG at the user's ear.
2005/88/EC: Conformity assessment procedure according to Annex VI. Notifi ed Body:
VDE Testing and Certifi cation Institute, Merianstr. 28,
63069 Off enbach, Germany
Measured sound power level ..............................................................................................
Guaranteed sound power level ...........................................................................................
Wear ear protectors!
Vibration information
Vibration total values (triaxial vector sum) determined according to EN 60745
Hammer-drilling in concrete:
Vibration emission value a
.................................................................................................
h
Uncertainty K= ....................................................................................................................
Chiselling
Vibration emission value a
.................................................................................................
h
Uncertainty K= ....................................................................................................................
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to compare one tool with another. It
may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for diff erent applications, with diff erent accessories or poorly maintained, the
vibration emission may diff er. This may signifi cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may signifi cantly
reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration such as: maintain the tool and the accessories, keep the hands warm, organisation of work patterns.
WARNING! Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
ROTARY HAMMER SAFETY WARNINGS
Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss.
Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal
injury.
Hold the power tool by insulated gripping surfaces only, when performing an
operation where the cutting accessory may contact hidden wiring or its own cord.
Cutting accessory contacting a "live" wire may make exposed metal parts of the power tool
"live" and could give the operator an electric shock.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when working with the machine. The
use of protective clothing is recommended, such as dust mask, protective gloves, sturdy
non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to health. Do not inhale the dust.
Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health (e.g. asbestos).
22
ENGLISH
K500 S
K545 S
...................................................................4632 71 04...
.........................4421 66 04... .................4422 01 04...
.........................4421 58 04... .................4421 96 04...
.........................4326 06 04... .................4324 51 04...
...000001-999999
...000001-999999
.......................... 1300 W............................. 1300 W
............................ 650 W............................... 650 W
.................................. .................................. 300 min
-1
.................................. .................................. 300 min
-1
.......................... 2840 min
........................ 2840 min
-1
-1
............................. 8,5 J ................................. 8,5 J
.................................. .................................... 45 mm
.................................. .................................... 65 mm
.................................. .................................. 100 mm
.............................. 66 mm .............................. 66 mm
............................. 6,3 kg ............................... 6,7 kg
.................................. ................................. 98,5 dB (A)
.................................. ............................... 109,5 dB (A)
.............................. 91 dB (A)
............................ 101 dB (A)
............................ 104 dB (A)
.................................. ..................................11,5 m/s
2
.................................. ................................... 1,5 m/s
2
............................11,5 m/s
2
............................... 9 m/s
2
............................. 1,9 m/s
............................ 1,9 m/s
2
2
Switch the device off immediately if the insertion tool stalls! Do not switch the device on
again while the insertion tool is stalled, as doing so could trigger a sudden recoil with a high
reactive force. Determine why the insertion tool stalled and rectify this, paying heed to the
safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING! Danger of burns
• when changing tools
• when setting the device down
Chips and splinters must not be removed while the machine is running.
Keep mains lead clear from working range of the machine. Always lead the cable away
behind you.
When working in walls ceiling, or fl oor, take care to avoid electric cables and gas or
waterpipes.
Clamp your workpiece with a clamping device. Unclamped workpieces can cause severe
injury and damage.
Always disconnect the plug from the socket before carrying out any work on the machine.
When working with large drill diameters, the auxiliary handle must be fastened in a right
angle with the main handle (see illustrations, section "Twisting the handle").
SPECIFIED CONDITIONS OF USE
K545 S:
The pneumatic hammer can be universally used for hammer drilling and chiselling
in stone and concrete.
K500 S:
The hammer can be used for chiselling in stone and concrete.
Do not use this product in any other way as stated for normal use.
EC-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility that the product described
under "Technical Data" fulfi lls all the relevant regulations and the directives 2011/65/EU
(RoHS), 2014/30/EU, 2006/42/EC, and the following harmonized standards have been
used:
EN 60745-1:2009+A11:2010
EN 60745-2-6:2010
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN 61000-3-2:2014
EN 61000-3-3:2013
EN IEC 63000:2018
Winnenden, 2021-01-21
Alexander Krug
Managing Director
Authorized to compile the technical fi le
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
GB-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility that the product described
under "Technical Data" fulfi lls all the relevant provisions of the following Regulations S.I.
2008/1597 (as amended), S.I. 2016/1091 (as amended), S.I. 2012/3032 (as amended) and
that the following designated standards have been used:
BS EN 60745-1:2009+A11:2010
BS EN 60745-2-6:2010
BS EN 55014-1:2017+A11:2020
BS EN 55014-2:2015
BS EN 61000-3-2:2014
BS EN 61000-3-3:2013
BS EN IEC 63000:2018
Winnenden, 2021-01-21
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
MAINS CONNECTION
Appliances used at many diff erent locations including wet room and open air must be
connected via a residual current device (FI, RCD, PRCD) of 30mA or less.
Connect only to single-phase AC current and only to the system voltage indicated on the
rating plate. It is also possible to connect to sockets without an earthing contact as the
design conforms to safety class II.
Make sure the machine is switched off before plugging in.
This is a device for professional use which may slightly exceed the guide values for current
harmonics when it is connected to the public low voltage mains supply. You should
therefore contact your energy supply company before you connect the device to the public
low voltage mains supply.
WORK WHEN IT'S COLD
If the tool is stored for a long period of time or at cold temperatures, the lubrication may
become stiff and the tool may not working initially or the working may be weak. If this
happens:
1. Insert a bit or chisel into the tool.
2. Run the tool against a scrap piece of concrete.
3. Pull and release the trigger every few seconds.
After 15 seconds to 2 minutes, the tool will start hammering normally. The colder the tool is,
the longer it will take to warm up.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all times.
Important note! If the carbon brushes are worn, in addition to exchanging the brushes the
tool should be sent to after-sales service. This will ensure long service life and top
performance.
If the supply cord of this appliance is damaged, it must only be replaced by a repair shop
appointed by the manufacturer, to avoid hazardous situations.
Use only Milwaukee accessories and spare parts. Should components need to be replaced
which have not been described, please contact one of our Milwaukee service agents (see
our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state the Article No. as well
as the machine type printed on the label and order the drawing at your local service agents
or directly at: Techtronic Industries GmbH, Max-Eyth-Straße 10, 71364 Winnenden,
Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Always disconnect the plug from the socket before carrying out any
work on the machine.
Please read the instructions carefully before starting the machine.
Accessory - Not included in standard equipment, available as an
accessory.
Do not dispose electric tools, batteries/rechargeable batteries
together with household waste material.
Electric tools and batteries that have reached the end of their life
must be collected separately and returned to an environmentally
compatible recycling facility.
Check with your local authority or retailer for recycling advice and
collection point.
Class II tool, tool in which protection against electric shock does not
rely on basic insulation only, but in which additional safety
precautions, such as double insulation or reinforced insulation, are
provided.
There being no provision for protective earthing or reliance upon
installation conditions.
European Conformity Mark
British Confomity Mark
Regulatory Compliance Mark (RCM). Product meets applicable
regulatory requirements.
Ukraine Conformity Mark
EurAsian Conformity Mark
ENGLISH
23
Publicité
