READ AND UNDERSTAND THESE INSTRUCTIONS COMPLETELY BEFORE INSTALLATION TO AVOID INJURY TO YOURSELF,
• AS SPECIFIED ON CARTON LABEL, ONCE PROTECTIVE FILM ON SHIELDS IS REMOVED, PRODUCT CANNOT BE RETURNED.
• AS SPECIFIED ON CARTON LABEL, DAMAGE CAUSED BY PACKAGING STAPLES IS NOT COVERED BY WARRANTY. ALL STAPLES MUST BE REMOVED PRIOR TO
• FAILURE TO FOLLOW THESE INSTALLATION INSTRUCTIONS COMPLETELY MAY VOID ANY WARRANTABLE COMPONENTS AND RESULT IN PRODUCT DAMAGE
• DO NOT USE LOCKTITE OR ANY OTHER SIMILAR FASTENER ADHESIVE. THESE TYPES OF PRODUCTS REACT TO PLASTICS AND CAUSE CRACKING. NOT
• OUR WINDSHIELDS ARE MADE FROM THE HIGHEST QUALITY MATERIAL PROVIDING OPTIMUM TRANSPARENCY AND CLARITY. BLURRINESS AND/OR
EXTRUSION MARKS MAY OR MAY NOT APPEAR WHEN LOOKING THROUGH WINDSHIELD FROM A WIDE, SIDE-ANGLE. THIS IS NORMAL FOR ALL EXTRUDED
These instructions contain important information for future reference and must be given to the customer at time of purchase or upon completion
ITEM
PART NAME
A
Windshield
B
Co-extruded bulb seal (¼")
C
W-type clamps set
D
Nuts & bolts
INSTRUCTION
Top pivot hinge of upper
BAG
E
windshield
Slide arm and lower pivot of
F
upper windshield
1. Installation
a) To apply the co-extruded bulb seal (Item B) to the windshield (Item A), find a
clean flat area where you can lay down the windshield. Partially remove the
protective film on both sides and apply the co-extruded bulb seal to the lower lip
using manual pressure to ensure good adhesion to the windshield. (The seal has
an internal steel wire structure, a wire cutter is required to cut the extra length)
b) To attach pivot components to the windshield (Item A), as per step a), find a clean
flat area where you can lay down the windshield. Partially remove the protective film where components (Item E & F) are to be
attached and follow drawings below. Do not tighten the screws that are passing through the windshield, they will be tightened
later in step d).
Upper
pivot
Locknut M6
Shoulder
washer M6
Button head
screw
Upper details
M6 x 18
2623 - Instructions POLARIS RANGER XP900 Full Tilt One Piece Ws - rev01
All manuals and user guides at all-guides.com
IMPORTANT NOTICES
DAMAGE TO THE VEHICLE OR ACCESSORY.
• FOR PROPER INSTALLATION, TWO PEOPLE ARE REQUIRED.
• TORQUE SPECIFICATIONS MUST BE FOLLOWED WHEN TIGHTENING BOLTS.
REMOVING PRODUCT FROM CARTON.
Parts List
(parts available with kit only and not available separately)
Includes : 4 socket cap screws M6 x 20, 6 locknuts M6, 10 button head screws M6 x 18, 8 internal lock
washers M6, 8 plastic shoulder washers M6, 4 button head screws M6 x 45 & 2 'T' knobs M6 x 35
Lower
Slide arm
pivot
Internal lock
washer M6
Lower details
INSTALLATION INSTRUCTIONS
POLARIS RANGER XP900
FULL TILT ONE PIECE WINDSHIELD
OR PERSONAL INJURY.
COVERED BY WARRANTY.
CLEAR PLASTIC MATERIALS.
DEALER
of installation.
DESCRIPTION
CNC windshield cut-out made of ¼" thick GE MR10 polycarbonate or equivalent
Includes : 54" of co-extruded bulb seal [end user to cut to exact length]
Includes : 2 W-type clamps
Includes : 2 x upper pivots & 4 x upper pivot cylinder adaptors
Includes : 2 x slide arms 3 positions & 2 x lower pivot mounts
Do not over-tighten the screws
that combine the slide arms with
the lower pivots, those parts
need to swivel.
PART # 2623
Co-extruded
bulb seal
Upper details
Lower details
WWW.KOLPIN.COM
QTY
1
1
2
1
1
1
1