Audizio PADOVA Manuel D'instructions page 7

Station presetting: While playing in DAB mode, press [Preset]. Turn the [Tune/Select] knob to select the desired preset slot
(1-30), press [Tune/Select] to store. Pressing and holding [Quick preset 1-5] will quickly save the current station to that
preset slot.
Press [Preset] to recall memory. Turn the [Tune/Select] knob to select the stored station you want to listen to. Press
[Tune/Select] to confirm. If stations are saved in slot 1, 2, 3, 4 or 5 it's possible to quickly recall them by pressing [Quick
preset 1-5].
Show channel information: Press [Menu/Info] repeatedly to show various forms of information regarding the station that is
being played.
To receive the ordinary FM stations, place the radio close to the window and extend the antenna as far as it can go to get the
best reception. You may need to adjust the direction of the antenna to improve reception.
Press [Mode] to select FM mode.
Press and hold [Tune/Select] to automatically scan for available FM stations. After completing the automatic search, press
[Preset] to enter the list with found stations. Rotate the [Tune/Select] knob to select another FM station. Press [Tune/Select]
to confirm. Press [Previous] or [Next] to manually fine tune frequency.
Rotate [Tune/Select] to adjust the volume level when playback is active.
Station presetting: While playing in FM mode, press [Preset]. Turn the [Tune/Select] knob to select the desired preset slot (1-
30), press [Tune/Select] to store. Pressing and holding [Quick preset 1-5] will quickly save the current station to that preset
slot.
Press [Preset] to recall memory. Turn the [Tune/Select] knob to select the stored station you want to listen to. Press
[Tune/Select] to confirm. If stations are saved in slot 1, 2, 3, 4 or 5 it's possible to quickly recall them by pressing [Quick
preset 1-5].
Show channel information: Press [Menu/Info] repeatedly to show various forms of information regarding the station that is
being played.
Before transmission between your BT device and the radio is possible, both devices must be coupled. This process is called
"pairing". The radio is served as a receiver, to receive the music stream to be played on the radio.
If you have already coupled to a BT device before, this connection will be restored automatically when both devices are in
range and BT operation has been selected on the radio. "Pairing" does not have to be repeated. This function may need to be
activated in your BT device, however.
• Press [Mode] to enter BT mode.
• Turn on BT streaming on your device. The device will scan for pairable BT devices in the reception range.
• Select "Audizio Padova" from the list with found devices.
• Start playback on your BT device. Playback now takes place emitting sound from the radio.
You can listen to the music stored in other audio device or smart phone via the radio, through the connection to the 3.5 mm
aux-in jack on the rear side. Use a cable with 3.5 mm pins at both ends, one end connected to the aux-in jack on the radio, the
other end connected to the earphone jack on the audio device (or line out socket if available).
Press [Mode] to choose AUX mode. Play music on the connected device, the sound will be emitted from the radio.
Setting an alarm
• Press and hold [Menu/Info] and enter 'main menu'.
• Rotate and press [Tune/Select] to select 'System Settings'.
• Rotate and press [Tune/Select] to select 'Alarms'.
• Rotate and press [Tune/Select] to select 'Alarm 1' or 'Alarm 2'.
• Rotate [Tune/Select] to scroll through each alarm setting. If you want to change a setting, press [Tune/Select]. You can set
the following alarm options:
On/Off: Rotate and press [Tune/Select] to choose to set the alarm.
Time: Rotate and press [Tune/Select] to adjust the hour of the alarm. Repeat to set the minutes of the alarm.
Source: Rotate and press [Tune/Select] to choose between 'DAB', 'FM' or 'Buzzer'.
Repeat: Rotate and press [Tune/Select] to choose between 'Once', 'Daily', 'Weekends' or 'Weekdays'.
Volume: Rotate and press [Tune/Select] to set the alarm volume.
This function allows programming the device to switch into standby mode by itself after a set period of time.
• Press and hold [Menu/Info] and enter 'main menu'.
• Rotate and press [Tune/Select] to select 'System Settings'.
• Rotate and press [Tune/Select] to select 'Sleep'.
7