Publicité
Cordless air pump
Permitted ambient temperat-
ure during operation and dur-
ing storage
Recommended rechargeable
batteries
Recommended battery char-
C)
gers
A) Measured with rechargeable battery PBA 18V 2.0Ah
B) Depends on battery in use
C) The following chargers are not compatible with the PBA re-
chargeable battery: AL 1814 CV, AL 1820 CV, AL 1860 CV
Noise/Vibration Information
Noise emission values determined according
to EN 62841‑1.
Typically, the A-weighted sound pressure level of the power
tool is 76 dB(A). Uncertainty K = 3 dB. The noise level when
working can exceed the volume stated. Wear hearing pro-
tection!
Vibration total values a
(triax vector sum) and uncertainty K
h
determined according to EN 62841‑1:
a
< 2.5 m/s², K = 1.5 m/s².
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Rechargeable battery
Bosch sells some cordless power tools without a re-
chargeable battery. You can tell whether a rechargeable bat-
tery is included with the power tool by looking at the pack-
aging.
Charging the battery
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Bosch Power Tools
Note: Lithium-ion rechargeable batteries are supplied par-
EasyInflate 18V‑500
tially charged according to international transport regula-
°C
–10 to +40
tions. To ensure full rechargeable battery capacity, fully
charge the rechargeable battery before using your tool for
the first time.
PBA 18V...W-.
Inserting the Battery
AL 18...
Push the charged battery into the battery holder until it
clicks into place.
Removing the Battery
To remove the rechargeable battery, press the battery re-
lease button and pull the battery out. Do not use force to do
this.
Battery charge indicator
The battery charge indicator indicates the remaining battery
capacity or an overload when the air pump is switched on.
LED
3 × continuous green light
2 × continuous green light
1 × continuous green light
1 × slowly flashing green light
The three LEDs in the battery charge indicator flash quickly
when the temperature of the rechargeable battery is outside
the operating temperature range and/or the overload protec-
tion has been triggered.
Recommendations for Optimal Handling of the
Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to
50 °C. Do not leave the battery in your car in the summer, for
example.
A significantly reduced operating time after charging indic-
ates that the battery has deteriorated and must be replaced.
Follow the instructions on correct disposal.
Mounting and Operation
You can use the adapter nozzle (8) with or without extension
by the hose (4) as needed.
When inflating items, fit the hose (4) and/or adapter
nozzle (8) on the air outlet (3). When deflating items, fit
them in the air inlet (2).
Insert the hose (4) into the air inlet (2) or onto the air
outlet (3) and turn it clockwise all the way.
Select the adapter nozzle (8) appropriate for the valve of the
item. Insert the adapter nozzle into the air inlet (2), onto the
air outlet (3) or onto the installed hose (4) as needed, and
turn it clockwise all the way.
If present, remove the valve seal on the item to be inflated.
To detach the hose (4) or adapter nozzle (8), turn it counter-
clockwise and take it off.
English | 11
Capacity
75–100 %
40–75 %
15–40 %
0–15 %
1 609 92A 7YW | (30.11.2022)
Publicité
