To Stop The Product; Maintenance Schedule - McCulloch B33 PS Manuel D'utilisation

Masquer les pouces Voir aussi pour B33 PS:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

To make the fuel mixture
Note: Always use a clean fuel container when you mix
the fuel.
Note: Do not make more than 30 days quantity of fuel
mixture.
1. Add half of the gasoline quantity.
2. Add the full quantity of oil.
3. Shake the fuel mixture to mix the contents.
4. Add the remaining gasoline quantity.
5. Shake the fuel mixture to mix the contents.
6. Fill the fuel tank.
To add fuel
Always use a fuel container with an antispill valve.
If there is some fuel on the container, remove the
unwanted fuel and let the container dry.
Make sure that the area near the fuel tank cap is
clean.
Shake the fuel container before you add the fuel
mixture to the fuel tank.
To start and stop
To start a cold engine
(Fig. 47)
1. Set the stop switch (A) to the start position.
2. Push the throttle lockout (B) and then pull the throttle
trigger (C).
3. While the throttle trigger is engaged, push the fast
idle button (D).
4. Release the throttle lockout and the throttle trigger.
5. Push the air purge bulb 10 times. The bulb does not
need to be completely filled. (Fig. 48)
6. Move the choke control to the full choke position.
(Fig. 49)
7. Hold the body of the machine on the ground with the
left hand. (Fig. 50)
8. Pull out the cord slowly with your right hand until you
feel some resistance.
9. Pull the starter cord quickly and powerfully. Repeat
approximately 5 times or until the engine attempts to
start.
WARNING: Read and understand the safety
chapter before you clean, repair or do
maintenance on the product.
18
10. Move the choke control to the no choke position.
11. Pull the starter cord quickly and powerfully until the
engine starts.
12. Let the engine run for 10 seconds.
13. Pull the throttle trigger to run at low speed for 60
seconds.
To start a warm engine
Note: Obey this procedure when you start a product that
has run out of fuel and has been refueled.
(Fig. 47)
1. Set the stop switch (A) to the start position.
2. Push the throttle lockout (B) and then pull the throttle
trigger (C).
3. While the throttle trigger is engaged, push the fast
idle button (D).
4. Release the throttle lockout and the throttle trigger.
5. Push the air purge bulb 10 times. The bulb does not
need to be completely filled. (Fig. 48)
6. Hold the body of the machine on the ground with the
left hand. (Fig. 50)
7. Move the choke control to the no choke position.
8. Pull out the cord slowly with your right hand until you
feel some resistance.
9. Pull the starter cord quickly and powerfully until the
engine starts.

To stop the product

Push the stop switch to stop the engine.
To start the engine when the fuel is too hot
If the product does not start, the fuel can be too hot.
Note: Always use new fuel and decrease the operation
time during warm weather.
1. Put the product in a cool area away from open
sunlight.
2. Let the product cool down for 20 minutes at
minimum.
3. Press the primer bulb again and again for 10-15
seconds.
4. Obey the procedure to start a cold engine. Refer to
To start a cold engine on page 18 .
MAINTENANCE

Maintenance schedule

Make sure that you obey the maintenance schedule.
The intervals are calculated from daily use of the
product. The intervals are different if you do not use the
product each day. Only do the maintenance work that is
860 - 001 - 28.10.2018

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

B33 ps+

Table des Matières