Accessories; Maintenance And Cleaning; Technical Data - Batavia BT-CCD001 Mode D'emploi

.
English
Selection:
Screwing
Drilling Masonry /
Concrete
Drilling Wood
Drilling Metal
*
• Select a low setting for small screws or
soft work material.
• Select a high setting for large screws, hard
work materials and when removing
screws.
• You should preferably choose a setting as
low as possible when driving screws.
Select a higher setting if the motor slips
before the screw is fully tightened.
WARNING: If the power tool gets excessively
hot in use, stop using the tool immediately and
allow to cool before continuing work. The cool-
ing period can be reduced by operating the
drill at maximum speed with no load. Always
make sure the Motor Vents (6) are not blocked
and do not allow dust to enter the body of the
tool through the Motor Vents; dust, especially
metallic dust, may damage or destroy the tool.
Switching the machine on and off
The on/off switch (13) is used for activating the
machine and adjusting rotation speed.
• Pressing the on/off switch (13) will activate
the machine, the further the switch is
being pushed, the faster the drill will turn.
• Releasing the on/off switch (13) will stop
the machine.
LED lamp
The LED lamp (14) will be lit automatically as
soon as you press the ON/OFF switch (13).

ACCESSORIES

Use only accessories with an allowable speed
matching at least the highest no-load speed of
the tool
10
7062504-Cordless_Combi_Drill-Ma-1702-06.indb 10
Mode selector Torque selector
1 – 16*
N/A
N/A
N/A
Speed
1
2
1 or 2
1 or 2

MAINTENANCE AND CLEANING

WARNING: Always disconnect from the mains
power supply, before carrying out any mainte-
nance/ cleaning of the charger. Remove the
battery before carrying out any maintenance/
cleaning of the tool.
Maintenance
There are no inner parts of the tool which need
maintenance.
Cleaning
• Keep safety devices, ventilation openings
and the motor housing as free as possible
from dirt and dust. Rub the electric power
tool with a clean cloth or blow over it with
low pressure compressed air.
• We recommend that you clean your elec-
tric power tool immediately after each use.
• Clean the electric power tool regularly with
a damp cloth and somewhat soft soap.
Do not use any cleaning or solvent materials;
these can attack the device's plastic compo-
nents. Make sure that no water can get inside
the electric power tool.

TECHNICAL DATA

Speed . . . . . . . . . . 0 – 350 / 1200 min
Impacts per Minute . . .0– 6000 / 20 000 min
Chuck . . . . . . . . . . . . . . . 2 – 13 mm
Torque hard/soft . . . . . . . . . . 25 / 48 Nm
Dimensions . . . . . . . . . . 23 × 10 × 22 cm
Weight . . . . . . . . . . . . . . . . . 1.28 kg
Sound Pressure Level L
pA
Uncertainty K . . . . . . . . . . . . . . 3 dB
pA
Sound Power Level L
WA
Uncertainty K . . . . . . . . . . . . . . 3 dB
WA
Hand Arm Vibration
(No Load) . . . . . . . . . . . . . . 0.748 m/s
(In Metal) . . . . . . . . . . . . . . 1.753 m/s
(In Masonry) . . . . . . . . . . . . 18.83 m/s
Uncertainty K . . . . . . . . . . . . . .1.5m/s
-1
-1
. . . . 80.80 dB(A)
. . . . . 91.80 dB(A)
2
2
2
2
27-09-17 09:18