Technical Data - Aerfast AC21025 Mode D'emploi

GB
1- DENOMINATION OF THE COMPONENTS

2- TECHNICAL DATA

AC21025
Power voltage / Frequency
Rated power
Max. operation pressure
Assured noise pressure level (Dir. 2000/14/CE)
Motor shaft rotation speed
Tank volume
Yield (sucked / delivered)
Ambient air temperature / humidity
Overall weight
Dimensions (bxlxh)
3- CE MARKING AND PLATE OF ASSURED SOUND PRESSURE LEVEL
CE Marking (FIG. 2 - Ref. 1) certifies the compliance of the machine with the essential safety and health requirements foreseen by the Machinery Directive 2006/42/CE. This plate (FIG. 2 - Ref.
2) certifies the compliance of the machine with the essential safety and health requirements foreseen by the Directive 2000/14/CE. They are represented by an adhesive plate in polyester with
black stamp by thermal transfer and they are stuck on the engine panel.
4- THE IMPORTANCE OF THE HANDBOOK
BEFORE USING THIS MACHINE, THE AUTHORIZED OPERATORS (SEE PAR. 2.2.1) MUST READ AND UNDERSTAND THIS MANUAL IN ALL ITS PARTS.
This manual of "Use and Maintenance Instructions" was drawn up according to the provisions foreseen by the "Machinery Directive" 2006/42/EC in order to assure an easy and correct compre-
hension of the contents handled by the authorized operators charged with the use and with the maintenance of this machine. Should the above mentioned operators detect any incomprehen-
sion while reading, please apply immediately to the manufacturer for correct explanations and further information in order to avoid wrong personal interpreting that could endanger safety. This
manual must at any time be available for the authorized operators. Therefore, it must always be placed, well guarded and preserved, near to the machine.
THIS MANUAL IS INTEGRAL PART OF THE MACHINE AND MUST BE PRESERVED FOR FUTURE REFERENCE UNTIL DISPOSAL OF THE SAME. THIS MANUAL MUST ALWAYS BE AVAIL-
ABLE FOR THE CHARGED OPERATORS AND HAS TO BE PLACED WELL STORED AND PRESERVED NEAR TO THE MACHINE.
THE MANUFACTURER CANNOT BE MADE LIABLE FOR DAMAGES TO PERSONS, ANIMALS AND THINGS, DUE TO THE INOBSERVANCE OF THE STANDARDS AND OF THE INSTRUC-
TIONS DESCRIBED IN THIS MANUAL.
THIS MANUAL HAS COMPULSORILY TO BE DELIVERED TOGETHER WITH THE MACHINE, IN CASE THIS LATTER IS TRANSFERRED TO ANOTHER USER.
THIS MANUAL MEETS THE STATE OF ART WHEN THE MACHINE IS TRADED AND CANNOT BE CONSIDERED IMPROPER JUST BECAUSE FOLLOWING TO NEW EXPERIENCES IT CAN
THEN BE UPDATED.
IN CASE OF LOSS OR WEAR OF THE MANUAL, REQUEST A NEW COPY FROM THE MANUFACTURER OR AUTHORIZED DEALER SPECIFYING THE MODEL OF THE MACHINE AND THE
REVISION QUOTED ON THE COVER.
V / Hz 230 / 50
HP 2
bar 9
dB 85
rpm 2800
litres 25
l/min 184 / 66
°C / % 5 - 40 / 5 - 95
kg 23
mm 545x340x605
AC21025
01) Cap Screw 26) Respirator
02) Spring washaer 27) Screw
03) Cylinder head 28) Oil sight class
04) Elbow 29) Screw
05) Soft Starter 30) O ring
06) Gasket 31) Oil seal
07) Valve board 32) Bearing
08) Aluminum Washer 33) Rotator
09) Valve block 34) Bearing
10) Valve gasket 35) Stator
11) Cylinder 36) Bracket
12) Piston cup 37) Spring washaer
13) Piston cup 38) Screw
14) Piston 39) Fan
15) Piston pin 40) Spring washaer
16) Spring washaer 41) Washer
17) Connecting Rod 42) Capcitor
18) Gasket 43) Capcitor insert
19) Cap Screw 44) Protector
20) Spring washaer 45) Screw
21) Crankcase 46) Foot Wheel
22) Crank shaft 47) Washer
23) Screw 48) Spring Washer
24) Cylinder seal cushion 49) Nut
25) Cylinder head 50) Nut
2
51) Washer
52) Foot pad
53) Screw
54) Pressure switch
55) Pressure gauge
56) Safety Valve
57) Double joint
58) Regulator
59) Ball valve
60) Power Cord Buckle
61) Pressure gauge
62) Wind Scooper
63) Washer
64) Screw
65) Unloading Pipe
66) Exhaust Pipe(Al)
67) Air fliter
68) Horizontal Tank
69) Power cord
70) Handgrip
71) Washer
72) Spring Washer
73) Screw
74) Check Valve
75) Ball valve