Technical Data - Milwaukee POS 13 Instructions D'utilisation

TECHNICAL DATA

Nominal power output ...........................................................
No load oscillation frequency ................................................
Orbital travel diameter ...........................................................
Dimensions of grinding plate .................................................
Weight without cable .............................................................
Typical weighted acceleration in the hand-arm area .............
Typical A-weighted sound levels:
Sound pressure level ..........................................................
The noise level when working can exceed 85 dB (A).
Wear ear protectors!
Measured values determined according to EN 50 144.
SAFETY INSTRUCTIONS
Please pay attention to the safety instructions in the
attached leaflet!
Appliances used at many different locations including open
air must be connected via a current surge preventing switch.
Always wear goggles when using the machine. It is
recommended to wear gloves, sturdy non slipping shoes
and apron.
Always disconnect the plug from the socket before carrying
out any work on the machine.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine.
Always lead the cable away behind you.
Before use check machine, cable, and plug for any
damages or material fatigue. Repairs should only be carried
out by authorised Service Agents.
Dust that arises when working in wood or using the tool on
industrial material can be dangerous to health. In this case
connect the tool to a suction device.
Do not use machines on any material containing asbestos.
This machine is suitable only for dry sanding.
SPECIFIED CONDITIONS OF USE
POS 13, PDS 13: The orbital sander can be used for
sanding wood, plastics and metal.
PRS 125 E: This eccentric sander is a versatile machine.
The following work can be carried out with it: Coarse
sanding and grinding, Fine sanding and polishing, Rubbing
down weather-beaten paint, Rubbing down weather-beaten
paint, Polishing up scratches on acrylic glass, Etc.
Do not use this product in any other way as stated for
normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is
in conformity with the following standards or standardized
documents. EN 50144, EN 55014-1, EN 55014-2,
EN 61000-3-2, EN 61000-3-3, in accordance with the
regulations 98/37/EC, 89/336/EEC
Manager Product Development
5 ENGLISH
Volker Siegle
POS 13 PDS 13
.........200 W ................... 200 W .................... 200 W
.....26000 min ........... 26000 min
-1
.............2 mm .................... 2 mm ...................... 2 mm
... 80x130 mm ......... 147/100 mm ............... ø 125 mm
............1,3 kg ......................1,25 kg ....................... 1,25 kg
.......< 2,5 m/s .............. < 2,5 m/s
2
...........75 dB (A) .............. 75 dB (A) ................ 75 dB (A)
MAINS CONNECTION
Connect only to single-phase a.c. current and only to the
system voltage indicated on the rating plate. It is also
possible to connect to sockets without an earthing contact
as the design conforms to safety class II.
ADVICE FOR OPERATION
POS 13 with self-adhesive Velcro base plate can also be
operated with sandpaper without self-adhesive Velcro
fastening (with the sandpaper clamping device). In this
case please place self-adhesive sanding paper underneath
to safe the coating of the base plate.
Only use original MIlwaukee sanding and polishing tools
with self-adhesive velcro fastening.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all
times.
Use only Milwaukee accessories and Milwaukee spare
parts. Should components need to be replaced which have
not been described, please contact one of our Milwaukee
service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the Article No. as well as the machine type
printed on the label and order the drawing at your local
service agents or directly at: Milwaukee Electric Tool,
Max-Eyth-Straße 10, D-71364 Winnenden, Germany.
SYMBOLS
Always disconnect the plug from the socket
before carrying out any work on the
machine.
PRS 125 E
. 14000-26000 min
-1 -1
............... < 2,5 m/s
2 2