Skil 0735 Notice Originale page 8

- clean ventilation slots J 2 regularly with a brush or
compressed air
• Regularly check the condition of the cutting head and the
tightness of nuts, bolts and screws
• Regularly check for worn or damaged components and
have them repaired/replaced when necessary
• Storage &
- store the tool indoors in a dry and locked-up place,
out of reach of children
- securely mount storage rail K on the wall with 4 screws
(not supplied) and horizontally leveled
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skil.com)
TROUBlESHOOTING
• The following listing shows problem symptoms, possible
causes and corrective actions (if these do not identify
and correct the problem, contact your dealer or service
station)
! switch off the tool and disconnect the plug before
investigating the problem
★ Tool does not operate
- power supply socket faulty -> use another socket
- extension cord damaged -> replace extension cord
★ Tool operates intermittently
- internal wiring defective -> contact dealer/service
station
- on/of switch defective -> contact dealer/service
station
★ Tool vibrates abnormally
- grass too high -> cut in stages
★ Tool does not cut
- line too short/broken of -> feed the line manually
★ Line cannot be fed
- spool empty -> replace spool
- line entangled inside spool -> inspect spool; rewind if
necessary
★ Line is not cut of to correct length -> remove cover from
cutting blade
★ Line keeps breaking
- line entangled inside spool -> inspect spool; rewind if
necessary
- trimmer incorrectly used -> only trim with the tip of the
line; avoid stones, walls and other hard objects; feed
the line regularly
ENVIRONmENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2012/19/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 9 will remind you of this when the need for
disposing occurs
DEClARATION OF CONFORmITY
• We declare under our sole responsibility that the product
described under "Technical data" is in conformity with the
following standards or standardization documents: EN
60335, EN 61000, EN 55014 in accordance with the
provisions of the directives 2006/95/EC, 2004/108/EC,
2006/42/EC, 2000/14/EC, 2011/65/EU
• Technical file at: SKIL Europe BV (PT-SEU/ENG1),
4825 BD Breda, NL
19.12.2013
NOISE/VIBRATION
• Measured in accordance with EN 60335 the sound
pressure level of this tool is 70 dB(A) and the sound
power level 90 dB(A) (standard deviation: 3 dB), and the
vibration <2.5m/s² (hand-arm method; uncertainty K =
1.5 m/s²)
• Measured in accordance with 2000/14/EC (EN/ISO
3744) the guaranteed sound power level LWA is lower
than 93 dB(A) (conformity assessment procedure
according to Annex VI)
Notiied body : KEMA, Arnhem, NL
Notiied body identiication number : 0344
• The vibration emission level has been measured in
accordance with a standardised test given in EN 60335; it
may be used to compare one tool with another and as a
preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for diferent applications, or with diferent
or poorly maintained accessories, may signiicantly
increase the exposure level
- the times when the tool is switched of or when it is
running but not actually doing the job, may signiicantly
reduce the exposure level
! protect yourself against the effects of vibration
by maintaining the tool and its accessories,
keeping your hands warm, and organizing your
work patterns
Coupe-bordures
INTRODUCTION
• Cet outil est destiné à couper les herbes et mauvaises
herbes sous les buissons ainsi que sur les pentes et les
bordures qui ne peuvent être atteintes avec une tondeuse
• Cet outil n'est conçu pour un usage professionnel
8
10
0735