Publicité
SAFETY INSTRUCTIONS
WARNING! User must read the product
manual to fully understand this product prior to
use, and follow all safety instructions as outlined in
the WORXAIR
Operator's Manual.
TM
CAUTION!The user must wear the appropriate
clothing and safety goggles when operating
this product. Be aware of all bystanders, pets and
objects in a close proximity.
DO NOT operate blower and attachments when
•
fatigued.
DO NOT overreach or stand on unstable support.
•
Keep good footing and balance at all times.
•
Never direct airflow towards bystanders. Always
be aware of the direction that the debris will be
thrown.
•
Use a face filter mask to avoid breathing dust and
debris.
WARNING: This product maybe contains lead,
phthalate or other chemicals known to the
State of California to cause cancer, birth defects and
other reproductive harm. Please wash your hands
after use.
ASSEMBLY AND OPERATION
1. ATTACH THE GUTTER KIT AS SHOWN IN
Fig. A:
Connect the (1, 2, 3) components by screwing
together. Snap the (3, 4) components together.
2. ASSEMBLING THE UNIVERSAL ADAPTOR
(1) Place the fabric side of the Universal Adapter
over the Blower Outlet and slide it on as far as
possible (B1.1).
WORX TURBINE
models -Place the fabric
TM
side of the Universal Adapter over the outlet
of the Fan Housing and slide it on as far as
possible(B1.2).
WORX TRIVAC
models - Place the fabric
TM
side of the Universal Adapter over the Vacuum
Outlet and slide it on as far as possible (B1.3).
Before operation, flip the blow/vac switch into the
vacuum mode.
PLEASE NOTE: Items can be vacuumed through
the vac inlet and pass through or become
clogged within the gutter kit. Please keep the vac
inlet away from objects while using the gutter kit.
WORX TURBINEFUSION
1) Attach the Adapter for TURBINEFUSION
the Fan Housing and turn the Adapter to the right
position according to the position as the arrow
shown on the Adapter. (B1.4)
2) Place the fabric side of the Universal Adapter
over the Adapter for TURBINEFUSION
it on as far as possible. (B1.4)
3) PLEASE NOTE: Only operate the
TURBINEFUSION
in Blow mode. Please
TM
remove the collection bag before operating.
GUTTERPRO Universal
Gutter Cleaning Kit
All manuals and user guides at all-guides.com
models
TM
with
TM
and slide
TM
(2) Check to make sure the strap is threaded through
the locking mechanism. Then pull to tighten the
strap (B2). Increase the tension by pulling the
latch up and down to tighten (B3). To loosen,
simply press the two outside latches down and
then pull the strap out from other side (B4).
(3) Test that the Universal Adapter will not slide off
of the blower outlet.
(4) If further tightening is needed, then pull the
middle latch up and down until the adapter
is tight. Please recheck if it will slide off of the
blower outlet. Realign and repeat these steps
if needed (B3). To loosen, simply press the two
outside latches down and then pull the strap out
from other side (B4).
PLEASE NOTE: The Universal Adapter may have
space between the Blower Outlet and Adapter Outlet
after installation.
To remove the adapter, simply press the two outside
latches down and loosen the strap to remove it from
the Blower Outlet (B4).
NOTE:
Use only enough Gutter Tube Extensions to
comfortably reach the inside of the gutter.
3. OPERATE ACCORDING TO Fig. C:
The Gutter Tube Nozzle can be adjusted to any
desired direction by rotating the Gutter Tube
Connecter as shown in Fig. D. Gutter cleaning
applications will vary. It is recommended to try
various positions to find the most effective working
position for the type of house and gutter design.
5
EN
Publicité
