Eaton NPFMA40L Information Sur L'installation Et L'entretien

NPFMA40L/50L LED Fixtures
Installation & Maintenance Information
APPLICATION
Pro Flood LED floodlights' construction is designed for use indoors and outdoors in
marine and wet locations, where moisture, dirt, corrosion, vibration and rough usage
may be present.
• IEC 60598-1 and IEC 60598-2-1
• Wet locations
• IP66
• CE marked
To avoid the risk of fire, explosion or electric shock, this product should be
installed, inspected and maintained by a qualified electrician only, in accordance
with all applicable electrical codes.
To avoid electric shock:
• Be certain electrical power is OFF before and during installation and
maintenance.
• Floodlight must be supplied by a wiring system suitable per local code with
an equipment grounding conductor.
To avoid burning hands:
• Make sure LEDs and drivers are cool to touch when performing
maintenance.
INSTALLATION
Mounting
Yoke Mount – Wall Mount Using Floodlight Yoke Only
1. Ensure that no less than two (2) operators move, or lift 50L fixture. Do not
use yoke as a contact point to move fixture, as it may become loose during
movement.
2. Using yoke mounting dimensions shown in Figure 5, mark and drill desired
location on mounting surface.
3. Secure floodlight yoke to surface using ½" bolts or lag screws (not provided).
WIRING
Wiring the Floodlight
1. Open lower enclosure cover/heat sink (as shown in Figure 1) by loosening nine
(9) #10-24 x 0.75" stainless steel cover screws using a 5/16" nut socket or flat
head screwdriver (see Figure 1). The heat sink cover should be removed by
pulling back on one corner of the top most edge to prevent damage to gasket.
NOTE: To avoid pinching hazard between heat sink cover and driver housing, ensure
that floodlight is oriented in vertical position before, and during, wiring procedure.
2. All components in the fixture are pre-wired so only line in, neutral and ground
need to be connected in the fixture using the supplied Wago connectors, using
methods that comply with all applicable codes. See Figure 2 for wiring diagram.
• Wire range from AWG 18-14 (0.75 - 2.5mm²) for neutral, and line (strip
length 0.43" [10.9mm]), and AWG 16-14 (1.5 - 2.5mm²) for ground
connections (strip length 0.43" [10.9mm]).
• Entries to driver housing shall be sealed, using HTL or STL, with
devices rated a minimum of IP66.
• Standard openings are M20, M25 or 3/4" NPT.
• Secure all electrical connections and wiring entry glands.
• Ensure that the following lengths for field wiring, internal to the driver
housing compartment, are followed:
– 5.5" ± 0.25" (140 ± 6mm) for ground wire
– 4.5" ± 0.25" (114 ± 6mm) for neutral wire
– 3.5" ± 0.25" (90 ± 6mm) for line in wire
• If through wiring to other 50L units, ensure that the supply wire is
installed in the lower fixture, and through wiring is installed in the upper
fixture. See wiring diagram (Figure 2) for further clarification.
IF 1845 • 03/19
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
WARNING
WARNING
LINE TERMINAL NEUTRAL TERMINAL
Copyright
Pro Flood LED floodlights are supplied for use with a choice of voltages:
• 100-277 VAC, 50/60 Hz and 108-250 VDC
• 347-440 VAC, 50/60 Hz
To avoid potentially unsafe operating conditions:
• Make sure the supply voltage is the same as the rated floodlight voltage.
• Do not operate in ambient temperatures above those indicated on the
floodlight nameplate.
• Use only replacement parts from Eaton's Crouse-Hinds Division.
• Use proper supply wiring as specified on the floodlight nameplate.
• All surfaces must be clean.
• LED compartment non-serviceable. Do not open.
• Before opening wiring compartment, electrical power to the floodlight
must be turned off. Keep tightly closed when in operation.
UPPER HOUSING
LOWER HOUSING
Cover/heat sink
GROUND TERMINAL
2019, Eaton's Crouse-Hinds Division
®
WARNING
DO NOT PLACE
ADDITIONAL WEIGHT
ON THE BACK COVER/
HEAT SINK
Figure 1
IF 1845
COVER BOLTS
Page 1