Maintenance And Cleaning; Troubleshooting - Invicon TwinLux Mode D'emploi

> To interrupt or stop the curing cycle, press again on the on/off switch (7).
m3 4.2 Extending the curing time during the curing cycle
Stand (6)
The curing time can be extended to the next longer cycle during operation as follows > Mount the light protection shield (8) over the LED light source (5).
The integrated stand (6) is used to position the light source at an appropriate distance
> Select the desired curing time by pressing the on/off and timer switch (7) as follows:
to the polymerization surface during the curing procedure.
TwinLux
On/off switch (7) Curing time
> To increase the curing time from 30 to 60 seconds, press the on/off switch (7)
Short touch (< 1 sec) 180 seconds
On/off and timer switch (7) for 2 seconds, while the 30-second cycle is in operation.
Sustained pressure (> 2 sec) Continuous light emission Continuously illuminated
> To increase the illumination time from 60 seconds to continuous operation,
The LED light source (5) is switched on and off by means of the on/off and timer switch
> To interrupt or stop the curing cycle, press again on the on/off switch (7). press the on/off switch (7) for more than 2 seconds, while the 60-second cycle
(7). The individual curing times are chosen by applying varying degrees of pressure to
is in operation.
the on/off and timer switch. As soon as the on/off switch is pressed down and the LED
source starts emitting light, the curing time indicator (11) lights up or starts blinking.
m3
4.2 Extending the curing time during the curing cycle
> To increase the illumination time from 180 seconds to continuous operation,
The curing time can be extended to the next longer cycle during operation as follows
Light protection shield (8) press the on/off switch (7) for more than 2 seconds, while the 60-second cycle
is in operation.
The light protection shield prevents uncontrolled light emission from the
TwinLux
LED source (5).
> To increase the curing time from 30 to 60 seconds, press the on/off switch (7)
for 2 seconds, while the 30-second cycle is in operation.
> To increase the illumination time from 60 seconds to continuous operation,
press the on/off switch (7) for more than 2 seconds, while the 60-second cycle
10
is in operation.
11
m3
> To increase the illumination time from 180 seconds to continuous operation,
press the on/off switch (7) for more than 2 seconds, while the 60-second cycle
is in operation.
3.3 Charging the battery
i
NOTE!
Prolonging the life of the battery
Curing time indicator (11)
Blinking
LED indicators
9
9 Power on indicator
10 Battery charge indicator
11 Curing time indicator
CAUTION!
Cleaning the surfaces of the device
Exposure to water may damage the light unit
> Do not hold the light unit under running water. Do not dip the light unit into water.

5 Maintenance and cleaning

Power on indicator (9)
> Do not allow fluid to enter the air vents (4).
The red light emitting LED (9) on the rear of the light shows whether the unit is
> Allow the device to dry for at least 5 minutes after cleaning.
If the surface of the curing light or LED light source (5) has become soiled, proceed
connected to the power supply:
as follows:
Power supply
> Clean surfaces with a damp cloth (methylated spirits containing detergent).
> Switch off the light unit.
LED is off
> Disconnect the plug (1) of the power pack from the light unit.
Continuously illuminated
If the air vents (4) are heavily contaminated with dirt, proceed as follows:
> Switch off the light unit.
CAUTION!
> Disconnect the plug (1) of the power pack from the light unit.
Battery charge indicator (10)
Cleaning the surfaces of the device
> Clean the air vents (4) with compressed air.
The red light emitting LED (10) on top of the light shows the amount of power left in
Exposure to water may damage the light unit
the battery (see also Section 3.2).

6 Troubleshooting

> Do not hold the light unit under running water. Do not dip the light unit into water.
> Do not allow fluid to enter the air vents (4).
i
Malfunction Possible problem
NOTE!
> Allow the device to dry for at least 5 minutes after cleaning.
Light unit switches Battery is
Exact indication of the amount of power left
off prematurely defective
> Clean surfaces with a damp cloth (methylated spirits containing detergent).
You are given a more precise indication of the amount of power left in the battery
after having carried out two to three curing cycles.
If the air vents (4) are heavily contaminated with dirt, proceed as follows:
> Switch off the light unit.
> Disconnect the plug (1) of the power pack from the light unit.
Curing time indicator (11)
> Clean the air vents (4) with compressed air.
The green light emitting LED (11) on top of the unit shows which curing setting has
been selected. The unit switches off automatically after the curing time has elapsed
6 Troubleshooting
(except for continuous operation).
Malfunction Possible problem
Curing time indicator (11)
Light unit switches Battery is
Fast blinking
off prematurely defective
Slow blinking
Continuously illuminated
TwinLux m3
No power supply No power supply
Battery is being Battery is being
charged with power charged with power
Solution
Have the light unit checked by an
authorized service centre or directly by
Invicon chemical solutions
Solution
TwinLux m3
Have the light unit checked by an
30 seconds –
authorized service centre or directly by
60 seconds 180 seconds
Invicon chemical solutions
Continuous light Continuous light
11
11
7
11