Bosch GSH 5 Professional Notice Originale page 11

Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Do not touch any application tools or adjacent housing
u
components shortly after operation. These can become
very hot during operation and cause burns.
Take care when carrying out demolition work using
u
the chisel. Falling fragments of the demolition material
could injure you or any bystanders.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Hold the power tool firmly with both hands and make
u
sure you have a stable footing. The power tool can be
more securely guided with both hands.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
The power tool is intended for chiselling work in concrete,
brick, stone and asphalt, as well as for driving in and com-
pressing with the appropriate accessories.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Dust protection cap
(2) Locking sleeve
(3) Chisel adjustment switch (Vario-Lock)
(4) Lock-on button for on/off switch
(5) On/off switch
(6) Auxiliary handle (insulated gripping surface)
(7) Handle (insulated gripping surface)
Technical Data
Demolition hammer
Article number
Bosch Power Tools
Demolition hammer
Rated power input
Impact rate
Impact energy per stroke
according to EPTA-Proced-
ure 05:2016
Tool holder
Lubrication
Weight according to EPTA-
Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Noise/Vibration Information
Noise emission values determined according to
EN IEC 62841-2-6.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 96 dB(A); sound power level
107 dB(A). Uncertainty K=3 dB.
Wear hearing protection
Vibration total values a
determined according to
EN IEC 62841-2-6:
Chiselling: a
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
GSH 5
Pull the plug out of the socket before carrying out any
u
GSH 501
work on the power tool.
3 611 C37 0..
W
-1
min
J
Central permanent
kg
(triax vector sum) and uncertainty K
h
2 2
= 13.0 m/s , K = 1.5 m/s
1 609 92A 8A5 | (21.09.2022)
English | 11
GSH 5
GSH 501
1100
2850
7.5
SDS max
lubrication
5.5
/ II