Product Description And Specifications; Product Features; Technical Data; Declaration Of Conformity - Bosch Intuvia 100 Notice D'utilisation D'origine

English – 2
Product Description and
Specifications
Intended Use
The Intuvia 100 on-board computer is designed to display
cycling data.
To access the full functionality of the eBike system and
Intuvia 100 on-board computer, you will need a compatible
smartphone installed with the eBike Flow app (available
from the Apple App Store or the Google Play Store), e.g. for
<Reset trip>.

Product Features

The numbering of the components shown refers to the illus-
trations on the graphics pages at the beginning of the
manual.
Bluetooth® button
(1)
(2) Battery compartment cover
Locking screw support
(3)
(4) On-board computer contact
Reset button
(5)
(6) Locking screw for on-board computer
Holder for on-board computer
(7)
(8) On-board computer cradle
(9) On-board computer
(10) Rubber seal
(11) Non-rechargeable battery (coin cell type CR2450)
(12) Slotted screwdriver
(13) Battery compartment
(14) Holder fastening screw
a) Not included in the scope of delivery
Display Elements of On-Board Computer
(a) Battery charge indicator
(b) Bike lights display
(c) Assistance level indicator
(d) Drive unit assistance indicator
(e) Unit indicator
(f) Text indicator
(g) Navigation bar
(h) Value indicator
(i) Speedometer

Technical Data

On-board computer
Product code
A)
Operating temperature
Storage temperature
Battery
0 275 007 3BI | (24.03.2022)
a)
Intuvia 100
BHU3200
°C −5 to +40
°C +10 to +40
1× CR2450
On-board computer
Protection rating
Weight, approx.
Bluetooth® Low Energy 5.0
– Frequency
– Transmission power
A) Temperatures outside of this range may cause faults in the dis-
play.
The licence information for the product can be accessed at
the following Internet address:
http://www.bosch-ebike.com/licences.

Declaration of Conformity

Robert Bosch GmbH, Bosch eBike Systems, hereby declares
that the Intuvia 100 radio communication unit complies
with Directive 2014/53/EU. The full text of the EU Declara-
tion of Conformity is available to view at the following web-
site: https://www.bosch-ebike.com/conformity.
Robert Bosch GmbH, Bosch eBike Systems, hereby declares
that the Intuvia 100 radio communication unit complies
with the Radio Equipment Regulations 2017 (SI
2917/1206). The full text of the UK Declaration of Conform-
ity can be accessed at the following Internet address:
https://www.bosch-ebike.com/conformity.
Assembly
Inserting and removing the on-board computer
(see figure A)
To insert the on-board computer, insert the lugs of the bat-
tery compartment (13) into the cradle (8) of the holder, and
press the on-board computer gently down. To lock, turn the
on-board computer clockwise until it engages.
To remove the on-board computer (9), turn it anticlockwise
and remove the on-board computer from the cradle (8).
Remove the on-board computer when you park the
u
eBike.
Inserting the locking screw (see figure B)
The on-board computer can be secured in place to prevent it
from being removed from the holder. The on-board com-
puter must be in the holder for this. Undo the fastening
screw (14) of the clamp with a hex key until the holder (7)
can be moved. Turn the holder (7) until the bottom side of
the on-board computer is accessible. Insert the locking
screw (6) and bolt it with the on-board computer. Align the
holder (7) correctly with the on-board computer and tighten
the fastening screw (14) again with a hex key.
Please note: The locking screw is not designed to prevent
theft.
Intuvia 100
IP54
g 63
MHz 2400–2480
mW ≤ 1
Bosch eBike Systems