Flotec FPSC2150A Notice D'utilisation page 2

Specifications and Safety
DESCRIPTION
This Submersible Sump Pump is designed for home
sumps. Unit is equipped with a 3-prong grounding-
type power cord. Shaded-pole motor is oil filled and
sealed for cooler running. Sleeve bearings on motor
shaft never need lubrication. Automatic reset thermal
protection.
SPECIFICATIONS
Power supply required ...........................115V, 60 HZ.
Liquid Temp. Range ................32°F to 70°F(0°-21°C)
Individual Branch Circuit Required (min.) ....15 Amps
Discharge:................................................1-1/2" FNPT
NOTICE: This unit is not designed for applications
involving salt water or brine! Use with salt water or
brine will void warranty.
Pump water only with this pump.
Do not use where water recirculates.
Not designed as a swimming pool drainer.
PERFORMANCE
TOTAL FEET (M)
Motor 5
Series HP (1.5m)
CAPACITY GALLONS(L)/HOUR
2760
FPSC2150A 1/3
(10 448)
3200
FPSC3150A 1/2
(12 113) (10 220) (7 570)
ELECTRICAL & SWITCH SPECIFICATIONS
Individual
Branch
Motor Circuit
Series HP Req.(Amps)
FPSC2150A 1/3 15
FPSC3150A 1/2 15
GENERAL SAFETY INFORMATION
Electrically powered sump pumps normally give
many years of trouble-free service when correctly
installed, maintained, and used. However, unusual
circumstances (interruption of power to the pump,
dirt/debris in the sump, flooding that exceeds the
pump's capacity, electrical or mechanical failure in
the pump, etc.) may prevent your pump from
functioning normally. To prevent possible water
damage due to flooding, consult your retailer about a
secondary AC sump pump, a DC backup sump
pump, and/or a high water alarm. See the
"Troubleshooting Chart" in this manual for
information about common sump pump problems
and remedies. For more information, see your
retailer, call Flotec customer service at
1-800-365-6832 or visit our website at
www.flotecwater.com.
For parts or assistance, call Flotec Customer Service at
1. Know the pump application, limitations, and
2. Do not use in water with fish present. If any oil
3. Disconnect power before servicing.
4. Release all pressure within system before
5. Drain all water from system before servicing.
6. Secure discharge line before starting pump. An
7. Check hoses for weak or worn condition before
8. Periodically inspect sump, pump and system
9. Provide means of pressure relief for pumps whose
10. Personal Safety:
No flow
10 15
at height
(3m) (4.6m)
shown
below
2160 1410 20 Ft.
(8176) (5337) (6.1M)
2700 2000 24 Ft.
11. When wiring an electrically driven pump, follow
(7.3M)
12. This equipment is only for use on 115 volt
*Switch Setting
in inches (cm)
On Off
7-1/2"(19) 3"(7.6)
7-1/2"(19) 3"(7.6)
13. All wiring should be performed by a qualified
14. Make certain power source conforms to
15. Protect electrical cord from sharp objects, hot
16. Do not touch an operating motor. Modern motors
potential hazards.
leaks out of the motor it can kill fish.
servicing any component.
unsecured discharge line will whip, possibly
causing personal injury and/or property damage.
each use, making certain that all connections are
secure.
components. Keep free of debris and foreign
objects. Perform routine maintenance as
required.
discharge line can be shut-off or obstructed.
a. Wear safety glasses at all times when working
with pumps.
b. Keep work area clean, uncluttered and
properly lighted – replace all unused tools
and equipment.
c. Keep visitors at a safe distance from work area.
d. Make workshop child-proof – with padlocks,
master switches, and by removing starter keys.
all electrical and safety codes that apply.
(single phase) and is equipped with an
approved 3-conductor cord and 3-prong,
grounding-type plug.
To reduce risk of electric shock,
pull plug before servicing. This pump has not
been investigated for use in swimming pool
areas. Pump is supplied with a grounding
conductor and grounding-type attachment plug.
Be sure it is connected only to a properly
grounded grounding-type receptacle.
Where a 2-prong wall receptacle is encountered,
it must be replaced with properly grounded
3-prong receptacle installed in accordance with
codes and ordinances that apply.
electrician.
requirements of your equipment.
surfaces, oil, and chemicals. Avoid kinking cord.
Replace or repair damaged or worn cords
immediately.
can operate at high temperatures.
1-800-365-6832
2