Roland XV-2020 Mode D'emploi page 145

❍Vibrato Rate (Controller number 76)
Status 2nd byte
BnH 4CH
n = MIDI channel number:
vv = Vibrato Rate value (relative change):
❍Vibrato Depth (Controller number 77)
Status 2nd byte
BnH 4DH
n = MIDI channel number:
vv = Vibrato Depth value (relative change):
❍Vibrato Delay (Controller number 78)
Status 2nd byte
BnH 4EH
n = MIDI channel number:
vv = Vibrato Delay value (relative change):
❍Effect 1 (Reverb Send Level) (Controller number 91)
Status 2nd byte
BnH 5BH
n = MIDI channel number:
vv = Reverb Send Level:
❍Effect 3 (Chorus Send Level) (Controller number 93)
Status 2nd byte
BnH 5DH
n = MIDI channel number:
vv = Chorus Send Level:
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 40H - 7FH (-64 - 0 - +63)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 40H - 7FH (-64 - 0 - +63)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 40H - 7FH (-64 - 0 - +63)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
MIDI Implementation (en anglais)
❍RPN MSB/LSB (Controller number 100, 101)
Status 2nd byte
BnH 65H
BnH 64H
n = MIDI channel number: 0H - FH (ch.1 - 16)
mm = upper byte (MSB) of parameter number specified by RPN
ll = lower byte (LSB) of parameter number specified by RPN
<<< RPN >>>
Control Changes include RPN (Registered Parameter Numbers), which are extended.
When using RPNs, first RPN (Controller numbers 100 and 101; they can be sent in any
order) should be sent in order to select the parameter, then
Data Entry (Controller numbers 6 and 38) should be sent to set the value. Once RPN mes-
sages are received, Data Entry messages that is received at the same MIDI channel after that
are recognized as changing toward the value of the RPN messages. In order not to make any
mistakes, transmitting RPN Null is recommended after setting parameters you need.
This device transmits the following RPNs.
RPN Data entry
MSB, LSB MSB, LSB Notes
00H, 00H mmH, llH Pitch Bend Sensitivity
mm: 00H - 18H (0 - 24 semitones)
ll: ignored (processed as 00H)
00H, 01H mmH, llH Channel Fine Tuning
mm, ll: 20 00H - 40 00H - 60 00H
(-4096 x 100 / 8192 - 0 - +4096 x 100 / 8192 cent)
00H, 02H mmH, llH Channel Coarse Tuning
mm: 10H - 40H - 70H (-48 - 0 - +48 semitones)
ll: ignored (processed as 00H)
00H, 05H mmH, llH Modulation Depth Range
mm, ll:
(0 - 16384 x 600 / 16384 cent)
7FH, 7FH ---, --- RPN null
RPN and NRPN will be set as "unspecified." Once
this setting has been made, subsequent
●Program Change
Status 2nd byte
CnH ppH
n = MIDI channel number: 0H - FH (ch.1 - 16)
pp = Program number: 00H - 7FH (prog.1 - prog.128)
3rd byte
mmH
llH
00 00H - 06 00H
145